STERO SD3 Series Скачать руководство пользователя страница 33

Страница: 33 / 71

ERROR CODES (IN SERVICE DIAGNOSTICS SCREEN)

Left Digit (1)

Right Digit (1)

Description of Error

Normal operation. No recorded errors.

Slow Leak.

Booster set point timeout (480 sec. after initial fill).

Control board E-prom error.

Water not to float on initial fill.

Float or temperature thermistor(s) open or connector J1 on control board

is open.

Wash thermistor error.

Rinse thermistor error.

Booster thermistor error.

SERVICE DIAGNOSTICS CHART

TEST

ACTIVE KEY

KEY RESPONSE

DISPLAY DATA

Recorded Error

▲ (arrow)

Reset recorded error(s)

Error messages (see ERROR

CODES table).

NOTE:

Only the most recent

error recorded for each digit (left/

right) are stored and displayed.

Previously recorded errors are

overwritten.

Select

Jump to display test.

Display Test

▲ (arrow)

Step through display test.

Sequences LED segments on

display board for test.

Select

Jump to Keypad Test.

CYCLE, ▲ and PROG

Switch Test

—

Pressing any of the switches

under test displays a

corresponding number for that

switch.

Display key number:

CYCLE (keypad) = 1

▲ (control board) = 2

PROG (control board) = 3

Select

Jump to Revision Level display.

Software Revision Level

Display

▲ (arrow)

No change

Display Revision Level of

Software.

Select

Jump to Wash Temp

Tank Temperature

Select

Jump to Rinse Temp

Tank temp and WASH icon.

Thermistor errors are indicated

as 'oP' or 'SP' for open or shorted

thermistors respectively.

Rinse Temperature

Select

Jump to Booster Temp

Rinse temp and RINSE icon.

Thermistor errors are indicated

as 'oP' or 'SP' for open or shorted

thermistors respectively.

Booster Temperature (AH

only)

Select

Jump to Cycle Counter Display

Booster temp and WASH/

RINSE icons. Thermistor errors

are indicated as 'oP' or 'SP' for

open or shorted thermistors

respectively.

SD3 Series - TROUBLESHOOTING

Page 33 of 37

F45576 (1015)

Содержание SD3 Series








































































Результаты поиска

Содержание SD3 Series

Отзывы:

Похожие инструкции для SD3 Series

Бренды по названию

Популярные бренды

STERO SD3 Series, Руководство по обслуживанию и запасным частям

Результаты поиска

Содержание SD3 Series

Отзывы:

Похожие инструкции для SD3 Series

Бренды по названию

Популярные бренды