SERVICE PROCEDURES AND ADJUSTMENTS
CONTROL BOARD
PROGRAMMING
Certain procedures in
this section require electrical test or
measurements while power is applied
to the machine. Exercise extreme
caution at all times and follow Arc Flash
procedures. If test points are not easily
accessible, disconnect power and
follow Lockout/Tagout procedures,
attach test equipment and reapply
power to test.
NOTE:
The control board is mounted in the machine
in such a way that the printing is upside down. The
control board will be depicted in the manual as it is
found on the machine for consistency purposes.
NOTE:
Prior to removing board from machine, check
and note the settings of the programmable variables
as outlined under SERVICE PROGRAMMING when
possible. When unable to access Service
Programming, check with establishment manager to
determine customer control settings.
NOTE:
The replacement control board will come
programmed as a different model. Step through this
procedure to set up the control board to function as an
SD3.
1.
Remove FRONT COVER.
2.
Open control door.
3.
Carefully short the two FACTORY pins of J5
together and press the ON key on switch
membrane keypad (user controls on front of
machine). Keep short across pins of J5 until
display indicates [ 88 ], then remove the short.
A.
Display will cycle between [ SET ty ] and
[ Sd, fd, GL, AS, HL, or St ].
NOTE:
SD3 machine type designation is [ St ].
Fig. 1
4.
Program the control board using the information
retrieved from the board being replaced and the
information found in CONTROL BOARD
PROGRAMMING table.
5.
Use the SELECT switch on control board to
select the feature and the (up arrow) switch to
change the feature settings.
Fig. 2
NOTE:
The display will alternate between the feature
and setting.
6.
Press OFF key on switch membrane keypad
(user controls on front of machine) to store
selections.
7.
Program the variables. Refer to SERVICE
PROGRAMMING.
8.
Close control door.
9.
Check machine for proper operation by running
one fill cycle and two normal cycles.
SD3 Series - SERVICE PROCEDURES AND ADJUSTMENTS
F45576 (1015)
Page 6 of 37
Содержание SD3 Series
