STERO SD3 Series Скачать руководство пользователя страница 21

Страница: 21 / 71

WASH LED on relay board turns
off.

Dishwasher enters a dwell cycle.
Default is two seconds.

Machine line voltage removed from
terminals DPS1 and DPS2.

Rinse cycle begins.

Control board energizes the fill/rinse
solenoid (1SOL) through the relay
board.

FILL LED on relay board turns on.

Control board energizes the rinse
feeder relay coil (1CR) through the
relay board. Relay 1CR N.O. contacts
4/2 and 8/6 operate (close).

The RINSE icon and final rinse
temperature are displayed.

Machine line voltage present at
terminals RPS1 and RPS2.

Rinse cycle continues for the
programmed time. Default is 10
seconds.

Rinse cycle completed.

Control board enters seven second
sani-dwell. RINSE icon is displayed
until sani-dwell cycle is complete.

Control board de-energizes the rinse
feeder 1CR through the relay board.
Relay 1CR de-energizes and 1CR
N.O. contacts 4/2 and 8/6 open.

Control board de-energizes the fill/
rinse solenoid 1SOL through the relay
board. Rinsing stops.

FILL LED on relay board turns off.

Machine line voltage removed from
terminals RPS1 and RPS2.

Tank temperature is displayed.

10. Tank Heat and Booster temperatures continue to

be monitored and maintained by the control
board through the relay board.

CONTROL and RELAY BOARD LEDs

CONTROL BOARD LEDs

CONTROL BOARD

DESCRIPTION

DOOR

On when door interlock 1LS is closed.

MICRO

Flashes at a rate of 1sec on, 1 sec off when machine is on.

WATER LEVEL

LOW - On when float switch 1FS is closed.

MID - Not used with SD3.

HIGH - Not used with SD3

RS485

Used with NAFEM Gateway.

RELAY BOARD LEDs

RELAY BOARD

DESCRIPTION

BOOSTER

On when triac Q3 (booster circuit) is gated on.

Booster heat on.

FILL

On when triac Q4 (fill circuit) is gated on. 1SOL on.

TANK HEAT AM

On when K9 is energized. Tank heat on.

EXT BSTR & VFC

On when machine is on.

WASH

On when K8 is energized. Pump motor on.

RINSE AID

On when triac Q2 (rinse feeder) is gated on. 1CR is energized.

SD3 Series - ELECTRICAL OPERATION

Page 21 of 37

F45576 (1015)

Содержание SD3 Series








































































Результаты поиска

Содержание SD3 Series

Отзывы:

Похожие инструкции для SD3 Series

Бренды по названию

Популярные бренды

STERO SD3 Series, Руководство по обслуживанию и запасным частям

Результаты поиска

Содержание SD3 Series

Отзывы:

Похожие инструкции для SD3 Series

Бренды по названию

Популярные бренды