STERO SD3 Series Скачать руководство пользователя страница 16

Страница: 16 / 71

ELECTRICAL OPERATION

COMPONENT FUNCTION

Control Board
Assembly . . . . . . . . . . . . .

Controls dishwasher electrical operation.

Relay Board . . . . . . . . . .

Controlled by control board assembly, the on board relays and fuses deliver energy to
machine control components.

Fuse, Relay Board
(F1) . . . . . . . . . . . . . . . . . . .

1/10A fuse. Protects rinse feeder 1CR coil circuit.

Fuse, Relay Board
(F2) . . . . . . . . . . . . . . . . . . .

1.0A fuse. Protects primary of transformer 2T, 1CON, 2CON, 3CON, 1SOL and external
booster control from over-currents.

Switch Membrane
Keypad . . . . . . . . . . . . . . .

User interface to machine. Used to select wash mode and program control board
assembly.

Display Module . . . . . . .

Provides machine information to user through the use of LEDs, lighted icons, and
illuminated text and numbers.

Contactor (1CON) . . . . .

Controls electrical power to wash pump (120VAC coil).

Contactor (2CON) . . . . .

Controls electrical power to wash tank heater (120VAC coil).

Contactor (3CON) . . . . .

Controls electrical power to booster heater (120VAC coil).

Relay (1CR) . . . . . . . . . . .

Controlled by the control board assembly through the relay board, provides a means of
controlling energy to RPS1 and RPS2 on terminal block 3TB.

Float Switch (1FS) . . . .

Detects water level in tank. On SD3, control board only uses Low Water Level LED with
the float switch.

Heater, Booster (BSTR
HTR) . . . . . . . . . . . . . . . . . .

Heating element for booster (8.5kW).

Heater, Tank (Tank
HTR) . . . . . . . . . . . . . . . . . .

Heating element for wash tank (5kW to 7.2kW).

High Limit Thermostat
(1TAS) . . . . . . . . . . . . . . . .

Protects tank heater circuit.

High Limit Thermostat
(2TAS) . . . . . . . . . . . . . . . .

Protects booster circuit. Frame mounted, capillary design

High Limit Thermostat
(3TAS) . . . . . . . . . . . . . . . .

Protects booster circuit. Mounted on the booster.

Interlock Switch
(1LS) . . . . . . . . . . . . . . . . . .

Feed back to control board on state of door (open or closed).

Solenoid (1SOL) . . . . . .

Fill/rinse solenoid.

Thermistor, Wash
(1QTM) . . . . . . . . . . . . . . . .

Senses tank water temperature.

Thermistor, Rinse
(2QTM) . . . . . . . . . . . . . . . .

Senses rinse water temperature

Thermistor, Booster
(3QTM) . . . . . . . . . . . . . . . .

Senses booster water temperature

Terminal Block
(1TB) . . . . . . . . . . . . . . . . . .

Line service to tank contactor 2CON (1 phase only).

SD3 Series - ELECTRICAL OPERATION

F45576 (1015)

Page 16 of 37

Содержание SD3 Series








































































Результаты поиска

Содержание SD3 Series

Отзывы:

Похожие инструкции для SD3 Series

Бренды по названию

Популярные бренды

STERO SD3 Series, Руководство по обслуживанию и запасным частям

Результаты поиска

Содержание SD3 Series

Отзывы:

Похожие инструкции для SD3 Series

Бренды по названию

Популярные бренды