STERO SD3 Series Скачать руководство пользователя страница 12 | Manualshive

Страница: 12 / 71

background image

INDIVIDUAL ELEMENT RESISTANCE

Voltage

Cold Resistance

575 - 600V

75.3 - 87.0Ω

PUMP MOTOR - TEST

Certain procedures in

this section require electrical test or
measurements while power is applied
to the machine. Exercise extreme
caution at all times and follow Arc Flash
procedures. If test points are not easily
accessible, disconnect power and
follow Lockout/Tagout procedures,
attach test equipment and reapply
power to test.

NOTE:

The pump motor for all machines is rated at 2

H.P. and has thermal overload protection.

1.

Remove FRONT COVER.

2.

Open control door.

3.

Apply power and measure incoming voltage
verifying it meets machine requirements.

4.

Turn machine on and take an amperage reading
of one of the tank heater leads connected to
contactor (2CON).

SD3 MOTOR CURRENTS (Maximum)

Voltage/phase

Amps

208/60/1

11.0A

240/60/1

10.6A

208/60/3

5.6A

240/60/3

5.4A

480/60/3

2.7A

NOTE:

Current consumption for a normally operating

pump and motor assembly will be less than the
amperage values listed.

5.

If motor current exceeds those values listed in the
table, inspect pump for blockage causing a
locked-rotor condition.

A.

If blockage is not present, replace motor.

6.

If current in one phase of a three phase motor is
low or missing, also inspect incoming line
service, contactor 1CON and other related
circuitry to missing phase.

THERMISTOR - TEST 1QTM, 2QTM

& 3QTM

Certain procedures in

this section require electrical test or
measurements while power is applied
to the machine. Exercise extreme
caution at all times and follow Arc Flash
procedures. If test points are not easily
accessible, disconnect power and
follow Lockout/Tagout procedures,
attach test equipment and reapply
power to test.

NOTE:

The temperature/resistance characteristics

are the same for all the thermistors used in SD3.

NOTE:

The resistance of each thermistor can be

measured by removing the plug connected to J2 on
the control board.

1.

Remove FRONT COVER.

2.

Open control door.

Quick Check Using Service Diagnostics

1.

Enter Service Diagnostics mode.

A.

Apply power. With machine off, press and
hold the PROG and SELECT switches on
control board and press and release the ON
key on the switch membrane keypad.

B.

Continue to hold in on the PROG and
SELECT switches until display shows [ 88 ]
then release both switches.

NOTE:

XXX represents the actual water temperature.

C.

Press the SELECT switch repeatedly until
[ WASH XXX°F (°C) ] which is tank water
temperature.

D.

Press the SELECT switch once to display
[ XXX°F (°C) RINSE ] which is rinse water
temperature.

E.

Press the SELECT switch once to display
[ WASH XXX°F (°C) RINSE ] which is
booster water temperature.

Measuring Thermistor Resistance

1.

Disconnect the plug from J2 on the control board.

SD3 Series - SERVICE PROCEDURES AND ADJUSTMENTS

F45576 (1015)

Page 12 of 37

«
...
10
11
12
13
14
...
»

Содержание SD3 Series








































































Отзывы:

Нет отзывов

Похожие инструкции для SD3 Series

Бренд: Zanussi Страницы: 20

Бренд: Zanussi Страницы: 34

Бренд: Russell Hobbs Страницы: 66

Бренд: Saba Страницы: 39

AQUALTIS AQ9L 29 U

Бренд: Ariston Страницы: 12

Бренд: grandimpianti Страницы: 85

Бренд: SPT Страницы: 21

Бренд: Maytag Страницы: 9

Бренд: GE Страницы: 3

Бренд: Miele professional Страницы: 56

Бренд: Maytag Страницы: 24

Бренд: ZANKER Страницы: 22

Бренд: Fagor Страницы: 33

Бренд: AEG Страницы: 48

Бренд: AEG Страницы: 32

Бренд: AEG Страницы: 56

Бренд: AEG Страницы: 24

Бренд: AEG Страницы: 24

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды