STERO SD3 Series Скачать руководство пользователя страница 35 | Manualshive

Страница: 35 / 71

background image

NOTE:

When troubleshooting, always check for

correct voltage, current, and resistance as specified
by the machine's data plate. Before troubleshooting
machine, verify that the control board assembly is
programmed to operate as an SD3.

VERIFY CONTROL BOARD is

CONFIGURED as an SD3

1.

Turn dishwasher off.

2.

Press the ON key on the switch membrane
keypad.

A.

Control board/display will begin a self-
check. When self-check completes,
machine type will be displayed briefly.

1)

AP (plain - external booster).

2)

AH (hot - self-contained booster).

3.

If machine type programmed into control board is
other than machine type on data plate, the control
board must be programmed before continuing.
Refer to CONTROL BOARD PROGRAMMING
as outlined in SERVICE PROCEDURES AND
ADJUSTMENTS.

4.

Check machine operation to see if problem still
exists.

ERROR CODE CHART

ERROR CODE CHART

Error Code

Explanation

Troubleshooting

E3

E1 - After wash cycle.

NOTE:

Shows Pd

while washing

1:15 cycle no rinse - E1

E2

Water did not reach the float during a

fill within 150 seconds.

Ensure drain lever is closed and the standpipe is

properly seated. Verify float is clear of debris.

Ensure the incoming water valve is open and water

flow/pressure is 20psi (+/- 5psi).

E6

Float and temperature thermistors

could not be detected.

Verify operation of float and temperature

thermistors. Ensure thermistor and door switch plug

is connected to J2 on control board.

Ed

Slow Leak. Machine enters fill cycle

three times with 35 minutes of initial

fill.

Ensure drain lever is closed and the standpipe is

properly seated with the O-ring clear of food soils

or other debris.

EE

Booster did not reach temperature

within eight minutes after initial fill.

Check to see that booster power is on. Check that

the water heater is on and supplying proper hot

water (min of 110°F).

EF

Severe internal control error.

Control board malfunction.

P1

Open or shorted wash tank

thermistor.

Check thermistor and switch thermistor and wiring.

P2

Open or shorted rinse thermistor.

Check rinse thermistor and wiring.

P3

Open or shorted booster thermistor.

Check booster thermistor and wiring.

TROUBLESHOOTING TABLE

NOTE:

Before troubleshooting machine,verify that

control board assembly is programmed to operate as

an SD3. Refer to CHECKING CONTROL BOARD
CONFIGURATION as oulined in this section.

SD3 Series - TROUBLESHOOTING

Page 35 of 37

F45576 (1015)

«
...
33
34
35
36
37
...
»

Содержание SD3 Series








































































Отзывы:

Нет отзывов

Похожие инструкции для SD3 Series

Бренд: Panasonic Страницы: 44

Бренд: Omega Страницы: 32

Бренд: Hanseatic Страницы: 70

Бренд: Roper Страницы: 36

Auto-Washer 1100 AC170

Бренд: Hoover Страницы: 10

Бренд: OZTI Страницы: 24

Бренд: Grundig Страницы: 116

Бренд: Saba Страницы: 47

Бренд: Ariston Страницы: 60

Бренд: Saivod Страницы: 62

Бренд: Swiss Страницы: 26

Бренд: Hanseatic Страницы: 84

SteamScrubber 45780 Series

Бренд: Labconco Страницы: 70

Бренд: PowerPoint Страницы: 19

Бренд: diLUSSO Страницы: 47

GE Profile PDW8500J

Бренд: GE Страницы: 2

Бренд: GE Страницы: 12

GE Profile PDW9800N

Бренд: GE Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды