Steris AMSCO 400 Series Скачать руководство пользователя страница 49

Страница: 49 / 174

5-13

Component Identification

Operator Manual

P129394-020

5.7 Printer

Refer to

Figure 5-10

Printer records all cycle data on 2-1/4" (57 mm) wide single-ply
paper. See

for

paper changing procedure. Printer functions controlled by touch-
screen pads are as follows:

•

Paper Feed

– (appears on typical In-cycle screen) Press to feed

out paper from the roll stored inside the control. Accessible
during all phases of operation, including alarm conditions. Press
and hold for continuous feed.

•

Status Print

– (appears on typical In-cycle screen) Press to

obtain a printout of current cycle phase and conditions (when
unit is in cycle). This touchpad is only visible during cycle
operation.

•

Print Last Cycle

– The sterilizer provides two methods for

acquiring an on-demand printout of the last cycle run.

PRINT LAST CYCLE

touchpad also appears on

Menu

screen (#2). Press to obtain a complete duplicate printout of
the last previously-run cycle (when unit is not in cycle).

Press

PRINT LAST CYCLE

touchpad on the Complete

screen (#5) during complete phase at end of cycle.

Automatic Duplicate Prin

t – The sterilizer can be set to

automatically provide a second printout at the end of each cycle.
Refer to

for information

on enabling this function.

Menu Screen

Typical In-Cycle Screen

Figure 5-10. Printer Features (Printer Door Open)

Take-Up

Spool

Printer Door

Inner Printer Door

Paper Feed Button

Содержание AMSCO 400 Series















































































































































































Результаты поиска

Содержание AMSCO 400 Series

Отзывы:

Бренды по названию

Популярные бренды

Steris AMSCO 400 Series, Руководство оператора

Результаты поиска

Содержание AMSCO 400 Series

Отзывы:

Бренды по названию

Популярные бренды