manualshive.com logo in svg

Steris AMSCO 400 Series, Руководство оператора

Поделиться
Скачать
Steris AMSCO 400 Series Скачать руководство пользователя страница 131

8-1

Routine Maintenance

Operator Manual

P129394-020

8.1  Preventive

Maintenance

The following preventive maintenance advisories must be observed: 

1.

Regular service and maintenance MUST be performed only by 
STERIS or a STERIS-trained technician. Any work performed by 
inexperienced or unqualified persons or the installation of 
unauthorized parts could cause personal injury, invalidate the 
warranty or result in costly damage.

2.

Under no circumstances should this equipment be serviced 
without the Maintenance Manual. The Maintenance Manual can 
be purchased by contacting STERIS Customer Service.

3.

A detailed Preventive Maintenance schedule and replacement 
parts list can be found in the Maintenance Manual. The 
Maintenance Manual can be purchased by contacting STERIS 
Customer Service.

4.

Preventive Maintenance is essential in keeping this equipment in 
optimal working condition. STERIS recommends establishing an 
annual maintenance agreement with STERIS service.

NOTE: Preventive Maintenance is not covered under warranty.

Inspection Frequency:

 The AMSCO

®

 400 Small Steam Sterilizer

must be inspected by a qualified service technician at least twice
each year while referring to 

M

AINTENANCE

  M

ANUAL

, P764334-453

.

(Actual frequency of equipment use may increase the number of
required inspections.) 

Operator inspections and procedures must be made on a daily,
weekly or as needed basis as indicated in 

S

ECTION

 8, R

OUTINE

M

AINTENANCE

.

WARNING – PERSONAL INJURY HAZARD and/or EQUIPMENT DAMAGE HAZARD:

•

Regularly scheduled preventive maintenance is required for safe and reliable operation of this equipment. 

Contact your STERIS Service Representative to schedule preventive maintenance.

•

The performance of the sterilizer is validated as a system including components defined by STERIS in the 

Operator Manual and Service Manual for the sterilizer. Substitution of unauthorized components can 
potentially lead to personal injury, damage or premature failure of the product and result in a unit 
configuration that is inconsistent with the validated product. STERIS warranty is void if components are 
used that are not approved. DO NOT USE components that are not validated as part of this sterilizer.

WARNING – ELECTRIC SHOCK and BURN HAZARD: Sterilizers may be equipped with up to three 
electrical connection points (sterilizer control, vacuum pump or integral steam generator). Each 
electrical supply must be provided with a separate disconnect. Disconnect all utilities to sterilizer 
before servicing. Do not service the sterilizer unless all utilities have been properly locked out. 
Always follow OSHA Lockout-Tagout and electrical safety-related work practice standards.

!

!

ROUTINE MAINTENANCE

8

Содержание AMSCO 400 Series















































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды