manualshive.com logo in svg

Steris AMSCO 400 Series, Руководство оператора

Поделиться
Скачать
Steris AMSCO 400 Series Скачать руководство пользователя страница 109

7-15

Cycle and Control Value Programming

Operator Manual

P129394-020

4.

If the Access Code is already enabled and 

ACCESS CODE

 

touchpad is pressed at the Change Machine Setup screen 
(#20), the display advances to screen #37 and the control 
prompts the user to enter the Access Code.

a.

Enter Code using the touchpads at the right of the screen.

b. Once the Code has been entered, press the 

ENTER

 

touchpad to advance to Select Access Code screen (#21).

5.

If the status of the Access Code does not need to be changed, 
press 

EXIT

 to return to the Change Machine Setup screen (#20).

7.6.2  Entering the Access

Code, Once Enabled

Once the Access Code has been set, any locked out functions or
cycle values are protected from unauthorized access. If any of these
locked out functions are selected, screen #37 appears on the
display.

1.

If the code is known, enter it using the touch-screen key pad. 
Once the entire four-digit code has been entered, press the 

ENTER

 touchpad. The access code digits are not displayed.

2.

If the code is not known, press 

CANCEL

 to return to the previous 

screen.

7.7  Lockout

This function is used to protect selected setup options from changes
by unauthorized personnel. Any functions selected for lockout
cannot be accessed without first entering the correct Access Code.
Items can also be unlocked at this screen. Small lock graphics
displayed in upper left hand corner of each touchpad indicate if item
is locked or unlocked. ( 

 =unlocked,    =locked.)

1.

To access this utility:

a.

Press 

MENU

 touchpad from the Status screen (#1) at the 

operating end of the sterilizer. 

b. The screen changes to show the Menu screen (#2).

c.

Press the 

CHANGE MACHINE SETUP

 touchpad, the 

display changes to the Setup screen (#20).

AN ACCESS CODE IS REQUIRED!

ENTER ACCESS CODE
OR PRESS CANCEL TO 
RETURN TO MENU.

ENTER

MENU

1

2

3

4

5

6

7

8

9

<-

0

->

37

Содержание AMSCO 400 Series















































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды