stayer AG L20, Руководство по эксплуатации

Страница: 15 / 32

es
/
15
/
it
gb
fr
p
cz
ASSEMBLING
Always make sure to switch off the tool and
to extract the battery cartridge before trying
to carry out any kind of operation at the
machine.
Installing the lateral grip
Before using the tool, always make sure
that the lateral grip is firmly installed.
Firmly screw the lateral grip 17 to the tool.
Installation or extraction of the disk guard
(Figs.3-4)
When suing a disk 10, the disk guard 6 must
be assembled to the tool in such a way that
the closed side of the guard always points
towards the user.
Assemble the guard 6 such that the protuberance
of the guard neck stays aligned with the bearing
housing. Thereafter, turn the guard 180º.
Make sure that the screw 21 is well tightened.
To extract the guard 6, follow the installation process
in reverse order.
nstallation or extraction of the grinding disk
(Figs. 2 - 3)
Always use the guard 6 as delivered when the
grinding disk 10 is on the disk 10 may break
during use and the guard 6 helps reducing
the possibilities of personal injuries.
Assemble the internal flange 11 on the spindle 9. Fit
the disk 10 on the internal flange 11 and screw the
external flange 12 on the spindle 9.
Fit the disk in a secure and correct position, such that
the machine’s direction of rotation coincides with
that of the disk according to the pointing arrows.
On abrasive disks the arrows are on the top side
and visible to the user.
To tighten the external flange 12, exert pressure on
the shaft lock 3 so that the spindle 9 cannot rotate,
and use the wrench 14 for the external flange 12 so
as to firmly adjust it clockwise.
To extract the disk 10, follow the installation process
in reverse order.
Never actuate the shaft lock the shaft is
moving.
CHARGER/BATTERY (FIGS. 4)
The SET is provided with two new lithium ion
batteries 8 which arrive prepared ready to
work; they must however overcome a period
of approximately 3 charges and discharges, to
achieve full performance.
When the battery 2 is new, it is sent in a low
charge condition. Charge the battery
completely before using your tool..
Assembly
To extract the battery from the machine, press stops
7 at the battery 2. Do not touch the metal terminals.
Take the charger base and connect it to the electric
grid.
The battery 2 is designed to fit in the charger 4 in a
single manner. This is to make sure that the positive
(+) and negative (-) polarities are in correspondence
with each other.
Insert the battery 2 and slightly press to set the
battery 2 firmly in the charger base.
Do not force the battery the other way
round into the base.
OPERATING INSTRUCTIONS
Simply insert the battery 8 into the charger 4.
Once the tool turns off for a lack of charge,
do not keep pressing the On/off switch as
this may damage the battery.
Advice
- Do not charge at temperatures lower than 0ºC
and higher than 45ºC, as this may seriously
damage the battery as well as the charger.
- Do not remove the battery while a job is being
carried out.
- If one foresees long periods of non-use of the
tool, the best is to disconnect the charger from
the power supply.
- When the lithium ion battery is empty, the tool
will turn off automatically.
- A period of less work after a charges indicates
that the battery is worn out and must be replaced.
ILLUSTRATED DESCRIPTION OF
FUNCTIONS (FIG. 1)
1. On/Off switch.
1b. Lock button switch.
2. Opening for strap.
3. Shaft lock.
4. Charger.
5. Charging status light.
6. Disk guard.
7. Battery clip.
8. Battery.
9. Spindle.
10. Grinding disk.
11. Internal flange.
12. External flange.
13. Soft grip.
14. Service wrench.
15. Air outlet opening.
16. Air inlet opening.
17. Lateral grip.