Speck pumpen VH 110 Скачать руководство пользователя страница 33 | Manualshive

Страница: 33 / 63

Speck pumpen VH 110 Скачать руководство пользователя страница 33

Operating Instructions

10/2010

1096.0799 | VU / VH Series

33

8 Troubleshooting

DANGER

Risk of injuries caused by running aggregate!

►

Do not touch the running aggregate.

►

Do not carry out any works on the running aggregate.

►

Prior to carrying out any assembly or maintenance works, de-energize the motor and protect it against restart.

RISK OF ELECTRIC SHOCK

Risk of death from electric shock!

►

Any electrical works must be carried out by qualified electricians only.

►

Observe the IEC 30364 (DIN VDE 0100) and for potentially explosive areas the IEC 60079 (DIN VDE 0165) standard.

WARNING

Risk of injuries caused by vacuum and harmful media to be pumped and operating liquid!

►

Use protective equipment when carrying out any works on the pump/aggregate.

►

Make sure the pump/aggregate is depressurized.

►

Drain the pump. Reliably collect operating liquid and media to be pumped and dispose of in an environmentally-compatible way.

If the machine operator is not able to rectify occurring defects himself, he has to call the person responsible for machine maintenance.
If the maintenance staff is not able to rectify the defect, the manufacturer has to be informed accordingly. The manufacturer will provide
troubleshooting support if he gets a detailed description of the defect.

Technical support address

Speck Pumpen Vakuumtechnik GmbH

Regensburger Ring 6 – 8, 91154 Roth / Germany
PO Box 1453, 91142 Roth / Germany
Phone: +49 (0) 9171 809 0
Fax:

+49 (0) 9171 809 10

E-mail:

[email protected]

Internet:

www.speck-pumps.de

.

Defect

Cause

Rectification

Motor does not start

Motor

One phase of the power supply is interrupted

►

Check the power supply, check the motor

Two phases of the power supply are interrupted

►

Check the power supply, check the motor

The motor protection switch has tripped

►

Switch on the motor protection switch

The motor is blocked

►

Check the motor

Pump is blocked

Impeller/inter casing is subject to corrosion

►

Use rust remover to overcome the blockage

of the pump

Ice inside the pump (solidified operating liquid)

►

Carefully heat up and defrost the pump

Contaminations or foreign bodies inside the pump

►

Flush/disassemble the pump, clean it

Pump calcification

►

Descale the pump

Blocked/defective impeller

►

Provide for a correct gap size of the inter

casing/impeller or replace

Defective motor bearing

►

Replace the motor bearing

«
...
31
32
33
34
35
...
»

Содержание VH 110
































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды