manualshive.com logo in svg

Speck pumpen VH 110, Руководство по эксплуатации

Поделиться
Скачать
Speck pumpen VH 110 Скачать руководство пользователя страница 31

 

Operating Instructions 

 

 

10/2010 

1096.0799 | VU / VH Series 

31 

9. 

Installation of bearing housing on discharge casing (non-
drive side) 

 

Force the bearing cover (360.1) into the bearing hous-
ing (330), adjust it and fasten it with hexagon head 
screws (901.1). 

 

Force the bearing housing into the discharge casing 
(107) and fasten it with hexagon head screws (901.3). 

 

Push the ring (500) onto the shaft. 

 

Press-fit the rolling bearing (320) into the bearing 
housing (330). 

 

Push the lock washer (931) onto the shaft. 

 

Screw the shaft nut (921) into position, tighten it and 
secure it with the lock washer (931). 

 

Force the bearing cover (360) into the bearing housing, 
adjust it and slightly fasten it with hexagon head 
screws (901.1). 

10. Pump 

adjustment 

 

Position the pump horizontally and adjust it on level 
ground. 

 

Tighten the hexagon nuts (920) of the casing bolts 
(563) crosswise. 

11.  Setting impeller position (non-drive side) 

 

Loosen the hexagon head screws (901.1) on the bear-
ing cover (360.1). 

 

Fasten the hexagon head screws (901.1) on the bear-
ing cover (360) until the impeller is in contact with the 
inter casing of the suction casing.  

 

Start the gauge at the front (drive side) of the shaft. 

 

Loosen the hexagon head screws (901.1) on the bear-
ing cover (360). 

 

Tighten the hexagon head screws (901.1) on the bear-
ing cover (360.1) until the impeller is in contact with the 
inter casing of the discharge casing. 

 

Halve the determined measure X and adjust the shaft 
by half the measure X (towards drive side).  

 

Fasten the shaft in this position by evenly tightening 
the hexagon head screws (901.1) on the bearing cov-
ers (360/360.1). 

 

Verify unobstructed movement of the pump. Manually 
rotate the pump shaft. 

12. Pipe 

installation 

 

Put the seals (400) and pipes (700) onto the suc-
tion/discharge flange, fasten them with hexagon head 
screws (901) and hexagon nuts (920). 

7.5.14  Assembly of VU/VH 500/600/ 

800/1200/1600 

 

Cross-sectional drawing VU 500/600/800/1200/1600  

 Cross-sectional drawing, page 59 

 

Cross-sectional drawing VH 500/600/800/1200/1600 

 Cross-sectional drawing, page 61 

1. 

Installation of valve flaps 

Not applicable to VH 500/600/800/1200/1600 and VU 500 
VU 600/1200/1600 inter casings (137/137.3) 
VU 800 inter casing (137.3)  

 

Put the stop plate (598/598.1) and the flap valve (746) 
onto the inter casings (137/137.1). 

 

Screw the hexagon head screws (901.5) with screw 
locking (Loctite®) into the inter casings. 

2. 

Installation of inter casings on suction/discharge casing 

 

Adjust the inter casing (137) (marks) and force it into 
the suction casing (106). 

 

Adjust the inter casing (137.3) (marks) and force it into 
the discharge casing (107). 

 

Screw hexagon socket head screws (914) through the 
suction/discharge casing into the inter casings and fas-
ten them. 

Additional steps for VH 800/1200/1600 

 

Adjust the inter casings (137.1/137.2) (mark), 
force them into position and compress them. 

Additional steps for VH 500/600 

 

Insert the packing gland (461) into the inter casing 
(137.2). 

 

Adjust the inter casings (137.1/137.2) (mark), 
force them into position and compress them. 

3. 

Installation of impeller and pump shaft 

 

Insert fitting keys (940/940.1) into the pump shaft (211) 
(non-drive side). 

 

Insert an O-ring (412) into the groove of the shaft pro-
tection sleeve (524). 

 

Push the shaft protection sleeve (524) and the lock 
washer (931) onto the pump shaft. 

 

Screw the impeller nut (922) onto the pump shaft.  

 

Vertically clamp the pump shaft with the drive side 
pointing up. 

VU 500/600/800/1200/1600 

 

Push the impeller (230) onto the pump shaft. 

 

The impeller blades must be tilted in the direction of rota-
tion. 
VH 500/600/800/1200/1600 

 

Push the impeller (230.1) onto the pump shaft. 

 

The impeller blades must be tilted in the direction of rota-
tion. 

 

Insert O-rings (412) into the grooves of the shaft 
protection sleeve (524.1). 

 

Push the shaft protection sleeve (524.1) onto the 
pump shaft. 

 

Push the inter casings (137.1/137.2) jointly over 
the shaft protection sleeve (523) . 

 

Insert the fitting key (940) into the pump shaft. 

 

Push the impeller (230) onto the pump shaft. 

 

The impeller blades must be tilted in the direction of rota-
tion. 

 

Insert the fitting key (940.1) into the pump shaft. 

 

Insert an O-ring (412) into the groove of the shaft pro-
tection sleeve (524). 

 

Push the shaft protection sleeve and the lock washer 
(931) onto the pump shaft. 

 

Screw the impeller nut (922) onto the pump shaft. 

 

Set the impellers in accordance with adjustment di-
mension L by turning the impeller nuts. 

 

Following the setting process, fasten the impeller nuts 
and secure them with the lock washers.  

4. 

Installation of stage casing and pump shaft 

 

Horizontally clamp the discharge casing (107) (inter 
casing on top). 

VU 500/600/800/1200/1600 

 

Insert the complete pump shaft (drive side point-
ing up) into the discharge casing (107), put down 
on inter casing (137.3). 

 

Force the stage casing (110) into the inter casing 
(137.3). 

VH 500/600/800/1200/1600 

 

Force the stage casing (110.1) into the inter cas-
ing (137.3). 

 

Insert the complete pump shaft (drive side point-
ing up) into the discharge casing (107). 

 

Adjust the inter casings (137.2/137.1) (markings), 
force them onto the stage casing (110.1) and put 
them down. 

 

Force the stage casing (110) into the inter casing 
(137.1). 

Содержание VH 110
































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды