Speck pumpen VH 110 Скачать руководство пользователя страница 19

Страница: 19 / 63

Operating Instructions

10/2010

1096.0799 | VU / VH Series

6.2.2 Switch-off

WARNING

Risk of injuries caused by vacuum or harmful media to be
pumped and operating liquid!

►

Use protective equipment when carrying out any works on

the aggregate.

Operating liquid: close fitting.

Switch off the motor.

Ventilation port (if available): open the fitting.

Check all connecting screws and tighten them if required
(only after initial commissioning).

CAUTION

Risk of aggregate damage resulting from vacuum condition!

►

Aerate the aggregate during switch-off.

►

Do not leave the aggregate under vacuum.



If the aggregate is not aerated, the mechanical seals will be
subject to damage.

6.3 Setting the operating liquid flow

rate

6.3.1 Continuous-flow

cooling

►

Switch on the aggregate.

►

Set the pressure in the operating liquid pipe to max. 0.2 bar

overpressure (



Diagram Fig. 13)

PIC

Fig. 13 Continuous-flow cooling

6.3.2

Open circulation cooling

►

Switch on the aggregate.

Set the pressure in the operating liquid pipe to max. 0.2 bar
overpressure (



Diagram Fig. 14, 15, 16)

PIC

Fig. 14 Open circulation cooling

PIC

TIC

Fig. 15 Open circulation cooling with temperature control

LIC

Fig. 16 Open circulation cooling with controlled liquid feed

►

Observe the permissible operating liquid temperature

(



Operating liquid, page 39)

Содержание VH 110
































































Результаты поиска

Содержание VH 110

Отзывы:

Бренды по названию

Популярные бренды

Speck pumpen VH 110, Руководство по эксплуатации

Результаты поиска

Содержание VH 110

Отзывы:

Бренды по названию

Популярные бренды