manualshive.com logo in svg

Speck pumpen VH 110, Руководство по эксплуатации

Поделиться
Скачать
Speck pumpen VH 110 Скачать руководство пользователя страница 17

 

Operating Instructions 

 

 

10/2010 

1096.0799 | VU / VH Series 

17 

 

Coupling guard has been disassembled. 

1. 

Take the measurements at the circumference of the cou-
pling in two planes with a 90° offset. 

2. 

Check the light gap towards the outer diameter using a 
straightedge (1): 

 

Position the straightedge over both coupling halves. 

 

Adjust the motor if you detect a light gap at the outer 
diameter (

Motor adjustment, page 17). 

3. 

Check the gap size using a feeler gauge (2): 

 

Permissible gap size (

 Dimension drawing, page 46 

et seq.). 

 

Use a feeler gauge to measure the gap (A) between 
the coupling halves. 

 

If the measured gap size is impermissible, adjust the 
motor (

 Motor adjustment, page 17). 

4. 

Install the coupling guard. 

5.9 Motor 

adjustment 

1. 

Adjust the motor in a way which ensures that the coupling 
halves are accurately aligned and use adjustment shims if 
required. 

2. 

Check the motor adjustment. 

3. 

Repeat the adjustment process if height or angular offset 
have not yet been fully compensated. 

4. 

Then, tighten the motor screws. 

5.10 Electrical connection 

 

RISK OF ELECTRIC SHOCK 

Risk of death from electric shock! 

►

  Any electrical works must be carried out by qualified electri-

cians only. 

►

  Observe the IEC 30364 (DIN VDE 0100) and for potentially 

explosive areas the IEC 60079 (DIN VDE 0165) standard. 

 

 

DANGER 

Risk of death from rotating parts! 

►

  Make sure to only operate the aggregate with all covers 

(fan hood) installed. 

 

5.10.1 Motor 

connection 

 

Observe the manufacturer's specifications for the motor. 

1. 

Connect the motor in accordance with the circuit diagram. 

2. 

Exclude any risk associated with electric power. 

3. 

Install an Emergency-Stop button. 

5.10.2  Checking direction of rotation 

 

DANGER 

Risk of death from rotating parts! 

►

  Use protective equipment when carrying out any works on 

the aggregate. 

►

  Keep an adequate distance to rotating parts. 

 

CAUTION 

Risk of material damage caused by dry running or incorrect 
direction of rotation! 

►

  Pump filled with operating liquid up to the middle of the 

shaft (

 Filling, page 18). 

 

1. 

Switch the aggregate on and immediately off again. 

2. 

Check whether the direction of rotation of the motor is in 
accordance with the arrow indicating the direction of rota-
tion on the aggregate. 

 

Wrong direction of rotation may result in damage and es-
cape of operating liquid at the mechanical seal. 

 

RISK OF ELECTRIC SHOCK 

Risk of death from electric shock! 

►

  Any electrical works must be carried out by qualified electri-

cians only. 

►

  Observe the IEC 30364 (DIN VDE 0100) and for potentially 

explosive areas the IEC 60079 (DIN VDE 0165) standard. 

 

3. 

In case of deviating direction of rotation: Swap the two 
phases. 

Содержание VH 110
































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды