manualshive.com logo in svg

Speck pumpen VH 110, Руководство по эксплуатации

Поделиться
Скачать
Speck pumpen VH 110 Скачать руководство пользователя страница 22

Operating Instructions 

 

 

 

22 

1096.0799 | VU / VH Series 

10/2010 

7.4 Preventing 

calcification 

 

Calcification results in excessive wear of moistened pump 
parts and increases the power consumption of the drive. 

 

2       4       6      8      10     12     14     16    18     20     22    24

9,0

8,5

8,0

7,5

7,0

carbonate hardness

 [°dH]

pH value

6,5

Area of protective coating 
and calcification

Equilibrium curve

Area of 
material abrasion

 

Fig. 18   Equilibrium characteristic 

• 

Operating liquid: Water 

• 

Water temperature: 17°C 

►

  pH value and carbonate hardness should intersect at a 

point which lies maxi. 0.2 above the equilibrium curve to 
avoid deposits and excessive corrosion in the aggregate. 

►

  Treat the operating liquid with a suitable agent. 

7.5 Disassembly 

 

DANGER 

Risk of injuries caused by running aggregate! 

►

  Do not touch the running aggregate. 

 

►

  Do not carry out any works on the running aggregate. 

►

  Prior to carrying out any assembly or maintenance works, 

de-energize the motor and protect it against restart. 

 

RISK OF ELECTRIC SHOCK 

Risk of death from electric shock! 

►

  Any electrical works must be carried out by qualified electri-

cians only. 

►

  Observe the IEC 30364 (DIN VDE 0100) and for potentially 

explosive areas the IEC 60079 (DIN VDE 0165) standard. 

 

 

WARNING 

Risk of injuries caused by vacuum and harmful media to be 
pumped and operating liquid! 

►

  Use protective equipment when carrying out any works on 

the pump/aggregate. 

►

  Make sure the pump/aggregate is depressurized. 

►

  Drain the pump. Reliably collect operating liquid and media 

to be pumped and dispose of in an environmentally-
compatible way. 

 

7.5.1 

Return to manufacturer 

 Aggregate 

shut 

down 

 Aggregate 

depressurized 

 

Pump completely drained 

 

Electrical connections isolated and motor secured  

against re-start 

 

Auxiliary operating systems shut down, depressurized 

and drained (if available) 

 

Connecting pipes removed 

 

Manometer lines, manometer and fixtures removed 

1. 

Loosen the fixing screws. 

2. 

Lift the aggregate out of the system (

Transport, page 11). 

3. Decontaminate 

pump/aggregate. 

 

4. 

Attach transport and sealing covers. 

5. 

Send a certificate of conformity to the manufacturer. 
If required, request a certificate of conformity from the 
manufacturer. 

7.5.2 Spare 

parts 

 

Spare parts are available from your supplier or the manu-
facturer. 

The following data are required for spare part orders.  
• 

Number of the pump/aggregate  
 (

Nameplate, page 9) 

• 

Type of pump/aggregate  
 (

Nameplate, page 9) 

• 

Item number of spare part  
(

Cross-sectional drawing, page 48 et seq.) 

• 

Designation of spare part  
(

Cross-sectional drawing, page 48 et seq.) 

• 

Number of spare parts 

7.5.3 Pump/aggregate 

repairs 

1. 

The following must be observed during assembly: 

 

Worn parts must be replaced by original spare parts. 

 

Replace the seals. 

 

Observe the specified tightening torques  
(

 Tightening torques, page 42). 

2. 

Clean all parts. 

3. 

Install the pump/aggregate inside the system  
(

 Set-up and connection, page 14). 

Содержание VH 110
































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды