SolarEdge SE100KUS Скачать руководство пользователя страница 89

Страница: 89 / 103

5. Disconnect all DC, AC wires and the communication connectors from the Primary

Unit.

Figure 47: Primary Unit interface

6. Unscrew the two conduit nuts in the Primary Unit securing it to the Connection

Unit.

Figure 48: Conduit nuts

7. Remove the screw securing the Primary Unit to the mounting bracket and remove

the Primary Unit from the mounting bracket.

NOTE

If you remove the Primary Unit and do not immediately install a new one,
use insulation tape to isolate any exposed wires.

8. Place the new Primary Unit on the mounting bracket; insert the screw securing the

Primary Unit through the right side of the heat sink and into the bracket.

9. Connect the DC, AC wires and the communication connectors to the Primary Unit.

10. For a 3 unit inverter reconnect the AC, DC and comm cables from the Connection

Unit to the right Secondary Unit.

11. Close the Primary Unit cover.

12. Perform the commissioning steps as described in

Activating, Commissioning and

Configuring the System Using the Inverter SetApp on page 43.

13. In the monitoring platform, use the

Replace

button in the

logical layout

tab (in site

Admin).

Three Phase Inverter with Synergy Technology Installation MAN-01-00402-1.2

Replacing the Primary Unit

Содержание SE100KUS








































































































Результаты поиска

Содержание SE100KUS

Отзывы:

Похожие инструкции для SE100KUS

Бренды по названию

Популярные бренды

SolarEdge SE100KUS, Руководство по установке

Результаты поиска

Содержание SE100KUS

Отзывы:

Похожие инструкции для SE100KUS

Бренды по названию

Популярные бренды