SolarEdge SE100KUS Скачать руководство пользователя страница 34

Страница: 34 / 103

Mark the location of the bracket screw and drill the hole

Fasten the bracket using a standard bolt

Verify that the bracket is firmly attached to the mounting surface .

Figure 17: Connection Unit bracket

9. Connect the Connection Unit cables to the Secondary Unit(s) connectors:

Communication cable to communication connector

AC cable to AC connector:

Position the cable so that the arrows are facing you.

Plug the AC cable into the Secondary Unit.

Rotate the cable connector clockwise to fasten it.

Figure 18: Connecting the AC connector to a Secondary Unit

NOTE

When connecting the AC cable to the left Secondary Unit, loop

the cable ( see the following figure) to prevent pressure on the

gland.

Chapter 3: Installing the Primary and Secondary Unit(s)

Three Phase Inverter with Synergy Technology Installation MAN-01-00402-1.2

Содержание SE100KUS








































































































Результаты поиска

Содержание SE100KUS

Отзывы:

Похожие инструкции для SE100KUS

Бренды по названию

Популярные бренды

SolarEdge SE100KUS, Руководство по установке

Результаты поиска

Содержание SE100KUS

Отзывы:

Похожие инструкции для SE100KUS

Бренды по названию

Популярные бренды