SolarEdge SE100KUS Скачать руководство пользователя страница 70

Страница: 70 / 103

6. For the switch/router side, use a pre-crimped cable or use a crimper to prepare an

RJ45 communication connector.

7. Connect the cable RJ45 connector to the RJ45 port of the Ethernet switch or

router.
You can connect more than one inverter to the same switch/router or to different
switches/routers, as needed. Each inverter sends its monitored data
independently to the SolarEdge monitoring platform.

NOTE

There are no LED indicators on the Ethernet connector, if the inverter is

not communicating with the monitoring platform through a LAN refer

Troubleshooting Communication on page 80.

8. The inverter is configured by default to LAN. If reconfiguration is required:

a. Verify the ON/OFF switch is OFF.

b. Verify the AC is on.

c. Close the cover and turn ON the Connection Unit.

WARNING!

ELECTRICAL SHOCK HAZARD. Do not touch uninsulated wires when

the Connection Unit cover is removed.

d. Use the SolarEdge SetApp to access the

Commissioning

main menu screen

as described in

Communication on page 45.

e. From the main menu tap

Communication

. The Communication screen is

displayed:

f. Select the following to configure the connection:

Server

LAN

LAN

DHCP

Enable

9. Verify the connection, as described in Verifying the Connection on page 73.

NOTE

The system automatically establishes communication with the

monitoring platform as it is configured to LAN by default.

Chapter 6: Setting Up Communication

Three Phase Inverter with Synergy Technology Installation MAN-01-00402-1.2

Содержание SE100KUS








































































































Результаты поиска

Содержание SE100KUS

Отзывы:

Похожие инструкции для SE100KUS

Бренды по названию

Популярные бренды

SolarEdge SE100KUS, Руководство по установке

Результаты поиска

Содержание SE100KUS

Отзывы:

Похожие инструкции для SE100KUS

Бренды по названию

Популярные бренды