SolarEdge SE100KUS Скачать руководство пользователя страница 24

Страница: 24 / 103

ON (1)

- Turning this switch ON (after optimizer pairing) starts the

operation of the power optimizers, enables power production and

allows the inverter to begin exporting power to the utility grid.

OFF (0)

- Turning this switch OFF reduces the power optimizer voltage

to a low safety voltage and inhibits exportation of power. When this

switch is OFF, the Primary and Secondary Units' control circuitry

remains powered up.

- Moving and releasing the switch allows viewing system information

via the LEDs and on the SolarEdgeSetApp mobile application screen
and performing functions:

P Position duration

Function

Comments

Switch moved to P for

less than 5 seconds

then released.

Displays production

information for 5 seconds

on the SetApp screen.

Displays error type

indications (if exist) for 5

seconds.

Activates the Wi-Fi access

point for connecting to the

SolarEdge Inverter

SetApp

While the

switch is in P,

all LEDs are

Switch moved to P for

more than 5 seconds

then released.

Starts pairing

WARNING!

Upon PVRSS, the internal circuitry remains up, therefore the inverter

cover must be opened only after shutting off the inverter ON/OFF

switch. This disables the DC voltage inside the Primary Unit. Wait five

minutes before opening the cover. Otherwise, there is a risk of electric

shock from energy stored in the capacitors.

LEDs

Chapter 3: Installing the Primary and Secondary Unit(s)

Three Phase Inverter with Synergy Technology Installation MAN-01-00402-1.2

Содержание SE100KUS








































































































Результаты поиска

Содержание SE100KUS

Отзывы:

Бренды по названию

Популярные бренды

SolarEdge SE100KUS, Руководство по установке

Результаты поиска

Содержание SE100KUS

Отзывы:

Бренды по названию

Популярные бренды