SolarEdge SE100KUS Скачать руководство пользователя страница 31

Страница: 31 / 103

Location

Clearance

Indoor Installation

Outdoor Installation

Locations where the

annual average high

temperature

(1)

below 25˚C / 77˚F

20 cm / 8"

between inverters

5 cm / 2" between

inverters (if inverters are

also installed one above

the other, maintain the

indoor installation

clearance)

Locations where the

annual average high

temperature

above 25˚C / 77˚F

40 cm / 16"

between inverters

3. If you are

not

using the level:

Position the mounting brackets against the wall and mark the required drilling
holes locations. The distance between neighboring holes from different brackets
should be 9 cm / 3-5/8"

Figure 14 to ensure a distance of 1.2" (3 cm) between

inverter units.

NOTE

Make sure to maintain the required distance between brackets and units,

otherwise the cables connecting the Secondary Unit(s) to the Connection

Unit may not reach the connectors.

(1)

Annual average high temperature – the average of the 12 monthly average highs,

for example:

Refer to

http://www.weatherbase.com/

to find the value in your location.

Three Phase Inverter with Synergy Technology Installation MAN-01-00402-1.2

Mounting and Connecting the Primary and Secondary Unit(s)

Содержание SE100KUS








































































































Результаты поиска

Содержание SE100KUS

Отзывы:

Похожие инструкции для SE100KUS

Бренды по названию

Популярные бренды

SolarEdge SE100KUS, Руководство по установке

Результаты поиска

Содержание SE100KUS

Отзывы:

Похожие инструкции для SE100KUS

Бренды по названию

Популярные бренды