manualshive.com logo in svg

SolarEdge SE100KUS, Руководство по установке

Поделиться
Скачать
SolarEdge SE100KUS Скачать руководство пользователя страница 29

Secondary Unit Interface

Figure 12: Secondary Unit bottom and side interfaces 

The Secondary units connectors are for connection to the Primary Unit:

DC (MC4) connectors

: for connection of the PV installation

Communication connector

: for communication options

AC connector

: for connection of the AC 

Mounting hole: 

for securing the unit to the bracket and for connecting an 

optional secondary grounding cable. 

Grounding screw

: for connecting an optional secondary grounding cable.

Mounting  and Connecting the Primary and 
Secondary Unit(s)

The inverter is typically mounted vertically, and the instructions in this 
section are applicable for vertical installation. Some SolarEdge  
inverters model can be installed horizontally (above 10° tilt) as well as 
vertically. For information and instructions for horizontal mounting refer 
to 

http://www.solaredge.com/sites/default/files/application_note_horizontal_

mounting_of_three_phase_inverters.pdf

First mount the Primary Unit then the Secondary Unit(s). 

Figure 13: Mounting bracket

NOTE

Make sure the mounting surface or structure can support the weight of the 
inverter and brackets, and make sure that it spans the width of the mounting 
brackets.

-

Three Phase Inverter with Synergy Technology Installation MAN-01-00402-1.2

28

   Secondary Unit Interface

Содержание SE100KUS








































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды