Snap-On ControlTech CTLNK1R240 Скачать руководство пользователя

Страница: 32 / 36



Battery Replacement

Note: When replacing batteries, real-time-clock will maintain date and time for 20 minutes.

Note: Turn End Cap clockwise to unscrew.

Replace 240 models with three "AAA" cells only.

Batteries should be installed in carrier prior to carrier installation into wrench.
Battery negative contacts should be oriented with carrier springs.

Replace all other models with three "AA" cells only.

Note: When Replace Battery screen is displayed wrench will no longer operate until batteries are

replaced. Only POWER button functions which immediately turns off wrench.



Memory Indicators

DATA IN MEMORY

MEMORY FULL

MEMORY ERROR

Less than 1500 torque and angle records stored in memory.

1500 torque or angle records stored in memory. New records will
not be recorded until memory is cleared.

Memory read or write error.

UNSCREW END CAP
INSERT NEW CELLS
POSITIVE (+) END
INTO HANDLE FIRST

LOW BATTERY

100% BATTERY

LEVEL

50% BATTERY

LEVEL

LOW BATTERY

REPLACE BATTERY

Содержание ControlTech CTLNK1R240





































Результаты поиска

Содержание ControlTech CTLNK1R240

Отзывы:

Похожие инструкции для ControlTech CTLNK1R240

Бренды по названию

Популярные бренды

Snap-On ControlTech CTLNK1R240, Руководство пользователя

Результаты поиска

Содержание ControlTech CTLNK1R240

Отзывы:

Похожие инструкции для ControlTech CTLNK1R240

Бренды по названию

Популярные бренды