Snap-On ControlTech CTLNK1R240 Скачать руководство пользователя

Страница: 14 / 36

BATCH COUNT screen is displayed next. Value can be changed by pressing UP/DOWN buttons. Once desired
batch count value has been set, press ENTER button.

PSET target screen is displayed labeled with same PSET number.

Note: Pressing ENTER button while

EXIT

menu selection is highlighted will exit without editing

PSET.

Deleting a Preset
Delete PSET function allows user to remove stored presets from wrench.
1.

From Preset screen to be deleted, press and hold UNITS button for 3 seconds.

CHANGE PRESET screen is displayed.

Highlight

DELETE

menu selection using UP/DOWN buttons and press ENTER button.

Target screen is displayed and deleted PSET is no longer available for selection.

Note: Pressing ENTER button while

EXIT

menu selection is highlighted will exit without deleting

PSET.

Note: When a PSET is deleted, all other stored PSET’s will retain their original PSET numbers.

When a new PSET is entered, it will be assigned first available PSET number in sequence.

100.0

FT-LB

CHANGE PRESET

DELETE

EDIT

EXIT

UNIT

button

held

Target Screen

UP/DOWN buttons

ENTER button

PSET 02

92°

Preset Angle Screen

CHANGE PRESET

DELETE

EDIT

EXIT

ENTER button

MAXIMUM

ANGLE

94°

ENTER
button

UP/DOWN buttons

BATCH COUNT

ENTER
button

UP/DOWN buttons

CHANGE PRESET

DELETE

EDIT

EXIT

PSET 02

01of04

92°

UNIT

button

held

Preset Angle Screen

UP/DOWN buttons

ENTER button

PSET 02

90°

Preset Angle Screen

CHANGE PRESET

DELETE

EDIT

EXIT

ENTER
button

UP/DOWN buttons

TARGET

ANGLE

92°

MINIMUM

ANGLE

90°

UP/DOWN buttons

ENTER
button

Содержание ControlTech CTLNK1R240





































Результаты поиска

Содержание ControlTech CTLNK1R240

Отзывы:

Похожие инструкции для ControlTech CTLNK1R240

Бренды по названию

Популярные бренды

Snap-On ControlTech CTLNK1R240, Руководство пользователя

Результаты поиска

Содержание ControlTech CTLNK1R240

Отзывы:

Похожие инструкции для ControlTech CTLNK1R240

Бренды по названию

Популярные бренды