Snap-On ControlTech CTLNK1R240 Скачать руководство пользователя | Manualshive

Страница: 3 / 36

background image

This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses, and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the following
measures:



Reorient or relocate the receiving antenna.



Increase the separation between the equipment and receiver.



Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.



Consult the dealer or an experienced radio/TV technician for help.

This device complies with Industry Canada license-exempt RSS standard(s). Operation is
subject to the following two conditions:
(1) This device may not cause interference, and
(2) This device must accept any interference, including interference that may cause
undesired operation of the device.

Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils
radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes :
(1) l'appareil ne doit pas produire de brouillage, et
(2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si
le brouillage est susceptible d'en compromettre le fonctionnement.

Note: During high-level Electrostatic Discharge events, temporary loss of function may
occur that requires operator intervention or system reset. As a precaution, discharge
non-energized work area prior to contact with screwdriver.

«
1
2
3
4
5
...
»

Содержание ControlTech CTLNK1R240





































Отзывы:

Нет отзывов

Похожие инструкции для ControlTech CTLNK1R240

Бренд: YOKOGAWA Страницы: 186

Бренд: Earlex Страницы: 4

Бренд: Lamello Страницы: 156

Бренд: Parkside Страницы: 156

Бренд: Parkside Страницы: 90

Бренд: Parkside Страницы: 39

Бренд: Parkside Страницы: 57

Бренд: Parkside Страницы: 51

Бренд: Elmdene Страницы: 8

Бренд: Grizzly Страницы: 48

Бренд: Milwaukee Страницы: 45

Бренд: SMC Networks Страницы: 2

Бренд: Cornwell Tools Страницы: 4

BiDi-Power Series

Бренд: tams elektronik Страницы: 16

Бренд: KEPCO Страницы: 2

Бренд: REAC Страницы: 15

Бренд: Paslode Страницы: 24

Бренд: Skil Страницы: 128

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды