Snap-On ControlTech CTLNK1R240 Скачать руководство пользователя

Страница: 21 / 36

Setting Target Tolerances
This function will allow user to set plus and minus tolerances for torque and angle targets.

Note: These tolerances are used for manual modes only. Preset tolerances are defined by

Minimum and Maximum values.

From Mode Setup menu, use UP/DOWN buttons to highlight tolerance selection to setup
(TQ-%, TQ+%, ANG-% ANG+%) then press ENTER button.

Tolerance screen is displayed.

Use UP/DOWN buttons to change tolerance value. Range is 0 to 10% (factory default for
minus tolerance is 0% and 4% for plus tolerance).

Press ENTER button to accept selection and exit to Mode Setup menu.

Note: Green progress lights turn on at target minus -% TOL.

Note: Red progress lights turn on above target plus +% TOL.

Note: Plus tolerance is added to minimum Preset value to define initial maximum value when a

Preset is first added.

Enable/Disable Torque THEN Angle Mode
This function will allow user to enable or disable Torque THEN Mode.

From Mode Setup menu, use UP/DOWN buttons to highlight

THEN DISABLED

(factory

default) selection then press ENTER button.

TQ THEN ANGLE enable/disable screen is displayed.

Use UP/DOWN buttons to select ENABLE or DISABLE selection.

Press ENTER button to accept selection and exit to Mode Setup menu.

Note: Menu selection indicates current configuration (ENABLED or DISABLED).

EXIT

TQ-% SETUP

TQ+% SETUP
ANG-% SETUP

UP/DOWN buttons

TORQUE -TOL%

TQ-% SETUP

TQ+% SETUP

ANG-% SETUP

ANG+% SETUP

ENTER

button

ANGLE +TOL%

ENTER

button

EXIT

TQ-% SETUP

TQ+% SETUP
ANG-% SETUP

UP/DOWN buttons

TQ+% SETUP

ANG-% SETUP

ANG+% SETUP

THEN DISABLED

TQ THEN ANGLE

ENABLE

DISABLE

ENTER

button

UP/DOWN buttons

TQ THEN ANGLE

ENABLE

DISABLE

ENTER

button

ENTER

button

TQ+% SETUP

ANG-% SETUP

ANG+% SETUP

THEN ENABLED

TQ+% SETUP

ANG-% SETUP

ANG+% SETUP

THEN DISABLED

Содержание ControlTech CTLNK1R240





































Результаты поиска

Содержание ControlTech CTLNK1R240

Отзывы:

Похожие инструкции для ControlTech CTLNK1R240

Бренды по названию

Популярные бренды

Snap-On ControlTech CTLNK1R240, Руководство пользователя

Результаты поиска

Содержание ControlTech CTLNK1R240

Отзывы:

Похожие инструкции для ControlTech CTLNK1R240

Бренды по названию

Популярные бренды