Snap-On ControlTech CTLNK1R240 Скачать руководство пользователя | Manualshive

Страница: 31 / 36

background image



USE OF ADAPTORS, EXTENSIONS AND UNIVERSALS

Anytime an adaptor, extension or universal is used with a torque wrench in such a way that
fastener distance is different than torque wrench square drive distance at calibration, an
adjustment to head length is required to get a proper fastener torque reading.

When using wobble extension or a universal, do not exceed more than 15 degrees of offset from
perpendicular drive. Do not use a long extension with flex-drive at full flex.



CALIBRATION

Contact your Snap-on sales representative for calibration services or refer to ControlTech

TM

Calibration Manual.



CERTIFICATION

This torque-angle wrench was calibrated at factory using angular displacement and torque
measurement instruments that are traceable to National Institute of Standards and Technology
(N.I.S.T.). Torque parameters comply with ISO 6789:2003 and ASME B107:300-2010 (B107.29).
Note: no U.S. or International Standards exist for angle wrenches.



MAINTENANCE / SERVICE

Clean wrench by wiping with a damp cloth. DO NOT use solvents, thinners or carburetor
cleaners. DO NOT immerse in anything.
Service and repairs are to be done by Snap-on Service Centers only. Contact your Snap-on Tools
representative.
Ratchet head repair kits can be ordered from a Snap-on Representative.

NOTES: - If display shows persistent "TORQUE ZERO ERROR" at power on, wrench is damaged

and must be returned for repair

- If display shows “ANGLE ERROR” in angle mode, fastener rotation speed has

exceeded capacity of wrench.

- Wrench must be held still during angle zeroing. Motion is indicated by alternating

dashes “- -” on display

- Remove battery when stored for extended periods (Note: clock will revert to default

settings).

IMPORTANT! Calibration events are recorded in wrench memory

which provides evidence to void factory certification.

«
...
29
30
31
32
33
...
»

Содержание ControlTech CTLNK1R240





































Отзывы:

Нет отзывов

Похожие инструкции для ControlTech CTLNK1R240

Бренд: Makita Страницы: 10

Бренд: Makita Страницы: 9

Бренд: Makita Страницы: 48

Бренд: Makita Страницы: 8

Бренд: Makita Страницы: 11

Бренд: Makita Страницы: 5

Бренд: Makita Страницы: 2

Бренд: Makita Страницы: 15

Бренд: Makita Страницы: 2

Бренд: Makita Страницы: 2

Бренд: Makita Страницы: 14

Бренд: Makita Страницы: 2

Бренд: Makita Страницы: 20

Бренд: Makita Страницы: 9

Бренд: Fein Страницы: 53

Бренд: Pattfield Ergo Tools Страницы: 88

00124507 Digi7800

Бренд: Hama Страницы: 20

Бренд: MULTIQUIP Страницы: 60

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды