Snap-On ControlTech CTLNK1R240 Скачать руководство пользователя | Manualshive

Страница: 28 / 36

background image

Control Box / ControlTechManager Report Mode Instrument Behavior

Set Headlength Behavior

1.

When switching the Control Box from Control Mode to Report Mode power off instrument.

2.

Change the Set Headlength Unit on the Control Box and or the ControlTechManager Qualifier Menu to
inches.

3.

Power down Control Box.

4.

Power on instrument.

5.

Enter SET HEADLENGTH menu on instrument (see page 6). Press UP/DOWN buttons simultaneously to
set factory default calibrated length. (J-Shank instrument will read 2.500 in).

6.

Power on Control Box.

7.

When executing PSETS from Control Box when using interchangeable head style instruments with
Snap-on “A” suffix torque adapters the PSET Headlength must be entered as 0 (zero) on the Control
Box Preset Headlength field the save the change. The Control Box interprets 0 as the default calibrated
length on J, Y, X and Z shank Interchangeable Heads Instruments.

8.

The Control Box Preset Set Headlength field will round down due to the Control Box native headlength
units are milometers. Example a J-shank instrument has a default calibrated length of 2.500 inches. The
Control Box will round down to 2.499 inches and will be viewed as such on the Control Box Preset Set
Headlength field after step 7 is performed.

9.

When adding a crows-foot adapters or any other adapter type to an interchangeable head instrument
that already has Snap-on “A” suffix adapter attached, the total combined effective length of the crows-
foot adapter and Snap-on “A” J, Y, X and Z adapters must be on the instrument SET HEADLENGTH
menu and or Control Box Control Box Preset Set Headlength field. See example in Figure 2 (head /
offset reference).

10.

Standard ratcheting head instruments the set headlength calibration default is always 0 (zero)
regardless of the torque range or ratchet drive size. Only a crows-foot adapter effective length needs
to be inputted. See example in Figure 3 (offset reference).

Table 1

Instrument Shank Size

Default Calibration

Length On Instrument

Control Box Default

Preset Set Headlength Field

J

2.500 inches

2.499 inches

Y

3.000 inches

2.999 inches

X

4.500 inches

4.499 inches

Z

5.750 inches

5.749 inches

ℎ𝑒𝑎𝑑

𝑜𝑓𝑓𝑠𝑒𝑡

𝑜𝑓𝑓𝑠𝑒𝑡

INTERCHANGEABLE HEAD

INSTRUMENT

STANDARD RATCHETING

HEAD INSTRUMENT

Figure 2

Figure 3

«
...
26
27
28
29
30
...
»

Содержание ControlTech CTLNK1R240





































Отзывы:

Нет отзывов

Похожие инструкции для ControlTech CTLNK1R240

Бренд: ZENS Страницы: 10

Бренд: Eriez Страницы: 12

Бренд: Desoutter Страницы: 8

Бренд: P.I.T. Страницы: 20

Бренд: SW-Stahl Страницы: 17

Бренд: RST Instruments Страницы: 16

Бренд: Velleman-Kit Страницы: 8

Бренд: Parkside Страницы: 51

Бренд: coocazoo Страницы: 18

Бренд: Qonnect Страницы: 4

Mobile Power Pack

Бренд: Socket Страницы: 2

Бренд: Panduit Страницы: 38

Бренд: MasterCraft Страницы: 24

Бренд: Total Страницы: 11

Бренд: One Stop Gardens Страницы: 8

Sorensen XHR 100-10

Бренд: Ametek Страницы: 82

Pro 3200 EVOLUTION

Бренд: Kemppi Страницы: 16

Бренд: Crestron Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды