Snap-On ControlTech CTLNK1R240 Скачать руководство пользователя | Manualshive

Страница: 5 / 36

background image

User Instructions Report Mode



Basic Functions (Quick Start)



Control Box Mode (Report)

Figure 1

Install three fresh Alkaline

“AA” cells into handle of wrench.

(

“AAA” for 240 models)

Wrench Power On Sequence
Note: Do not turn on wrench while torque is applied, otherwise torque zero offset will be incorrect and wrench

will indicate a torque reading when torque is released. If this occurs, re-zero wrench by momentarily
pressing POWER button while wrench is on a stable surface with no torque applied.

1.

Turn On Wrench.

While holding wrench still, monetarily press POWER button. Snap-on logo will be displayed followed
by torque and angle re-zeroing screens (if angle mode has been previously selected). If real-time-
clock has not been set, date and time entry screens are displayed (see Advanced Configuration
section for entering date and time). After entering date and time or if time has been previously set,
target TORQUE or ANGLE screen will now be displayed depending on previous measurement mode
selected.

2.

Select Measurement Mode.

Toggle between target TORQUE and ANGLE screens by repeatedly pressing ENTER button.

MODE

COUNT

AUDIBLE

ALERT

MODE SELECT AND MENU ENTRY BUTTON

INCREMENT

BUTTON

ON/OFF AND

RE-ZERO
BUTTON

DECREMENT

BUTTON

LCD BACKLIGHT

AND

PEAK TORQUE/ANGLE

RECALL BUTTON

UNITS AND

PRESET ENTRY

BUTTON

TORQUE AND/OR

ANGLE DISPLAY

BATTERY

CONDITION

PROGRESS

LIGHTS

PROGRESS

LIGHTS

DATA

STORAGE

ALERT

PROGRESS LIGHTS
Yellow

- First light indicates 40% of target

torque or angle reached, Second
indicates 60% of target reached,
Third indicates 80% of target
reached.

Green

- Indicates target torque or angle

reached.

Red

- Indicates exceeded torque or

angle target plus 4% or exceeded
maximum Preset target

.

TORQUE ZEROING

ANGLE ZEROING

--

SET STILL

UP/DOWN buttons

00

250.0

FT-LB

00

180°

SET DATE

2014

/01/01

YR MON DAY

ENTER

button

SET TIME

12

: 00 : 00

HR MIN SEC

UP/DOWN buttons

ENTER
button

Target Angle Screen

Target Torque Screen

WRENCH

LOCKED

ALERT

SIGNAL

STRENGTH

INDICATOR

«
...
3
4
5
6
7
...
»

Содержание ControlTech CTLNK1R240





































Отзывы:

Нет отзывов

Похожие инструкции для ControlTech CTLNK1R240

Бренд: ABIKOR BINZEL Страницы: 56

Бренд: Ganz Страницы: 8

Бренд: V-TAC Страницы: 16

NEWMAR Sentinel

Бренд: Mission Critical Страницы: 28

Бренд: Earlex Страницы: 5

EnergyGrind-100

Бренд: PEUGEOT Страницы: 10

Бренд: Parkside Страницы: 60

Бренд: Omega Lift Страницы: 36

Бренд: FDT Страницы: 4

Бренд: Panduit Страницы: 2

Бренд: Xantrex Страницы: 76

Бренд: Parkside Страницы: 258

Бренд: Villager Страницы: 147

Бренд: Agilent Technologies Страницы: 47

Бренд: TSPROF Страницы: 17

Бренд: Daewoo Страницы: 24

PPH SS 670 PENDULUM ACTION JIGSAW

Бренд: Parkside Страницы: 12

Бренд: G&G Technics Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды