Smartbitt SBOL50KTIII-3 Скачать руководство пользователя страница 21 | Manualshive

Страница: 21 / 57

Smartbitt SBOL50KTIII-3 Скачать руководство пользователя страница 21

21

7.3 LCD Display Icon

Display

Function

Backup time information

Indicates the backup time in pie chart.

Indicates the backup time in numbers.

H: hours, M: minutes, S: seconds

Fault information

Indicates that the warning and fault occurs.

Indicates the fault codes, and the codes are listed in details in section

3-9.

Mute operation

Indicates that the UPS alarm is disabled.

Output & Battery voltage information

Indicates the output voltage, frequency or battery voltage.

Vac: output voltage, Vdc: battery voltage, Hz: frequency

Load information

Indicates the load level by 0-25%, 26-50%, 51-75%, and 76-100%.

Indicates overload.

Indicates the load or the output is short.

Programmable output information

Indicates that the programmable outputs are working.

Mode operation information

Indicates the UPS connects to the mains.

Indicates the battery is working.

Indicates the bypass circuit is working.

Indicates the ECO mode is enabled.

Indicates the Inverter circuit is working.

Indicates the output is working.

Battery information

Indicates the Battery capacity by 0-25%, 26-50%, 51-75%, and 76-

100%.

Indicates the battery is unconnected

Indicates low battery level and low battery voltage.

Input & Battery voltage information

Indicates the input voltage or frequency or battery voltage.

Vac: Input voltage, Vdc: battery voltage, Hz: input frequency

«
...
19
20
21
22
23
...
»

Содержание SBOL50KTIII-3


























































Отзывы:

Нет отзывов