manualshive.com logo in svg

Skyshark IL-2 Sturmovik, Руководство пользователя

Поделиться
Скачать
Skyshark IL-2 Sturmovik Скачать руководство пользователя страница 24

Align and glue F1B to F1A, F2B to F2A, F3B to F3A, F4B to
F4A and F5B to F5A. Make sure the holes in F5A match the
pushrod locations on the plans (the printed number should
face rearward). 

F5B must also be exactly straight or the

cockpit floor will not align correctly. 

Glue F12B in place on F12A

Fit and glue the C1 cockpit floor in the tabs in F5B and F12B.
Insure the laser etching is facing down.

Carefully Slide F6B into the first slots in C1. Glue in place as
shown to the cockpit floor and the edges of F6A. Make sure
the pushrod holes are aligned with the holes in F5B.

Repeat for F7B thru F10B. 

IMPORTANT:

Insure the

pushrod holes are on the correct side so the rudder and
elevator pushrods line up correctly. 

Fit F11 in the last slot in C1 with the scribed line and number
facing rearward.

Fit and glue 1/8" x 1/4" x 36" balsa to the bottom slot in F1B
thru F12B. Note the stringer will extend back to F18 but don't
glue past F12B at this time. Do this on both sides of the for-
mers.This will be used as the crutch for the lower sheeting so
it should not be even with the top sheeting.

Содержание IL-2 Sturmovik




















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды