manualshive.com logo in svg

Skoda Octavia II 2004, Руководство по ремонту


Поделиться
Скачать
background image

 

 

 

 

 

 

 

 

 

 

 

 

 

Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted 

unless authorised by 

ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability 

with respect to the correctness of information in this document. Copyright by 

ŠKODA AUTO A. S.

�

 

– Lever the sensor -1- carefully and slowly from the retaining

plate -2- at the recess -3- using a suitable cross-head screw‐

driver.

Note

When removing, make sure to lever off the complete sensor and

not only the upper shell of the sensor.

Installing
Installation is carried out in the reverse order. When installing,

observe the following:

Caution

♦ Thoroughly clean the windscreen inside the retaining plate

with e.g. isopropyl (technical alcohol).

♦ The surface (coupling cushion) of the sensor must not get

dirty or damaged when installing. A sensor with a dam‐

aged coupling cushion must be replaced.

Note

If the surface (coupling cushion) of the sensor is dirty, it can be

cleaned, if necessary, by sticking on one or several adhesive

tapes and then pulling them off again.

– If necessary, remove the protective cap of the new sensor.

– Insert the sensor -1- into the retaining plate on the windscreen

-2- and press firmly.

Note

♦

Even after correct installation of the sensor, smaller air bub‐

bles can be present initially between the windscreen and the

coupling cushion. The contact surface must be free of bubbles

after approx. 10 minutes.

♦

When replacing, the new sensor must be coded with the ⇒ Ve‐

hicle diagnostic tester.

Octavia II 2004 ➤ , Octavia II 2010 ➤

Electrical system - Edition 12.2013

2. Windscreen Wiper and Washer System    

93

Содержание Octavia II 2004












































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Octavia II 2004

Technibel AO 15 GTS Installation Instructions Manual preview
AO 15 GTS
Бренд: Technibel Страницы: 16
MAXA MI26A User'S And Installer'S Manual preview
MI26A
Бренд: MAXA Страницы: 44
Ohyama woozoo AP45-M User Manual preview
woozoo AP45-M
Бренд: Ohyama Страницы: 72
Airwell Aqu@Scop Advance R410A User & Installation Manual preview
Aqu@Scop Advance R410A
Бренд: Airwell Страницы: 134
SAIKO AC-9110CL Instruction Manual preview
AC-9110CL
Бренд: SAIKO Страницы: 16
Pur Line COOLY 14000 User Manual preview
COOLY 14000
Бренд: Pur Line Страницы: 112
Daikin ROOM AIR CONDITIONERS Operation Manual preview
ROOM AIR CONDITIONERS
Бренд: Daikin Страницы: 17
AireSpa ASWRB100 Use & Care Manual preview
ASWRB100
Бренд: AireSpa Страницы: 20
Daikin FXFQ20M8V3B Installation And Operation Manual preview
FXFQ20M8V3B
Бренд: Daikin Страницы: 16
Daikin FXFQ20BVEB Installation And Operation Manual preview
FXFQ20BVEB
Бренд: Daikin Страницы: 20
Daikin FXFQ07TVJU Operation Manual preview
FXFQ07TVJU
Бренд: Daikin Страницы: 20
Daikin Super Multi NX 4MXS68F2V1B Installation Manual preview
Super Multi NX 4MXS68F2V1B
Бренд: Daikin Страницы: 19
Haier AS25XCHHRA-NR Operation Manual preview
AS25XCHHRA-NR
Бренд: Haier Страницы: 66
Haier AS35RBAHRA-PL Service Manual preview
AS35RBAHRA-PL
Бренд: Haier Страницы: 61
Samsung AWT17XSHDA Owner'S Instructions Manual preview
AWT17XSHDA
Бренд: Samsung Страницы: 31
Samsung AZ09A0KE Owner'S Instructions Manual preview
AZ09A0KE
Бренд: Samsung Страницы: 16
Kabel Salon Maestro Quick Start Manual preview
Salon Maestro
Бренд: Kabel Страницы: 11
Daikin FXFQ25SVM Installation Manual preview
FXFQ25SVM
Бренд: Daikin Страницы: 20

Бренды по названию

Популярные бренды

Загрузить еще бренды