Skoda Octavia II 2004 Скачать руководство пользователя страница 92

Страница: 92 / 203

Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted

unless authorised by

ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability

with respect to the correctness of information in this document. Copyright by

ŠKODA AUTO A. S.

�

– Carefully lever the angled pieces off the spray nozzles from

below and disconnect the plug connections (of the heated

nozzles).

– Unclip the nozzles from the cooling water tank cover.

Note

The spray nozzles can be adjusted. Adjust the spray nozzles

⇒ Maintenance ; Booklet Octavia II .

Installing
The installation occurs in reverse order.

1.3

Removing and installing rear window

spray nozzle Octavia

Removing
– Run wiper until it is in park position.
– Open cap of rear window wiper.
– Carefully pull out the spray nozzle in -the direction of arrow-.
Installing
– Push spray nozzle fully into the wiper arm shaft so that the

opening of the spray nozzle is facing parallel to the wiper arm.

1.4

Removing and installing rear window

spray nozzle Octavia Combi

Removing
The spray nozzle is located in the high level brake light.
– Remove high level brake light

⇒ page 131

– Remove spray nozzle.
Installing
The installation occurs in reverse order.

1.5

Adjusting spray jet

– In middle of swept area.

1.6

Repairing washer fluid lines

All notes and comments to this chapter can be found in the Work‐

shop Manual ⇒ Electrical system - General notes ⇒ Electrical

system - General notes; Rep. gr. 92 .

Octavia II 2004 ➤ , Octavia II 2010 ➤

Electrical system - Edition 12.2013

Rep. gr.92 - Windscreen wash/wipe system

Содержание Octavia II 2004












































































































































































































Результаты поиска

Содержание Octavia II 2004

Отзывы:

Бренды по названию

Популярные бренды

Skoda Octavia II 2004, Руководство по ремонту

Результаты поиска

Содержание Octavia II 2004

Отзывы:

Бренды по названию

Популярные бренды