Skoda Octavia II 2004 Скачать руководство пользователя страница 115

Страница: 115 / 203

Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted

unless authorised by

ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability

with respect to the correctness of information in this document. Copyright by

ŠKODA AUTO A. S.

�

Work procedure
The headlight on the left
– Only remove protective foil on the reverse side of the foil in the

area -1-.

– Glue the self-adhesive foil as shown in the figure, place onto

the parting plane -arrow- on the left-hand side of the headlight

glass and press forcefully in the area -1-.

– Carefully pull off the -clearer- mounting part of the foil from the

lens shown in the figure.

– On the lens there is only the protective foil -1-.
The headlight on the right

– Only remove protective foil on the reverse side of the foil in the

area -2-.

– Glue the self-adhesive foil as shown in the figure, place onto

the parting plane -arrow- on the right-hand side of the head‐

light glass and press forcefully in the area -2-.

– Carefully pull off the -clearer- mounting part of the foil from the

lens shown in the figure.

– On the lens there is only the protective foil -2-.

Note

Inform the customer about the corresponding notes for removing

the residual adhesive after pulling off the protective foil, e.g. tex‐

tiles soaked in isopropyl alcohol (do not use any aggressive

solvent, which can damage the polycarbonate lenses).

Octavia II 2004 ➤ , Octavia II 2010 ➤

Electrical system - Edition 12.2013

1. Headlights – halogen headlights

107

Содержание Octavia II 2004












































































































































































































Результаты поиска

Содержание Octavia II 2004

Отзывы:

Бренды по названию

Популярные бренды

Skoda Octavia II 2004, Руководство по ремонту

Результаты поиска

Содержание Octavia II 2004

Отзывы:

Бренды по названию

Популярные бренды