manualshive.com logo in svg

Skoda Octavia II 2004, Руководство по ремонту


Поделиться
Скачать
background image

 

 

 

 

 

 

 

 

 

 

 

 

 

Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted 

unless authorised by 

ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability 

with respect to the correctness of information in this document. Copyright by 

ŠKODA AUTO A. S.

�

 

7

Loudspeaker system

⇒ “7.1 Removing and installing loudspeakers”, page 74

7.1

Removing and installing loudspeakers

⇒ “7.1.1 Removing and installing the front bass loudspeaker”,

page 74
⇒ “7.1.2 Removing and installing the rear bass loudspeaker”,

page 74
⇒ “7.1.3 Removing and installing the front treble speaker”,

page 75
⇒ “7.1.4 Removing and installing the rear treble speaker”,

page 75
⇒ “7.1.5 Removing and installing the front midrange speaker”,

page 75
⇒ “7.1.6 Removing and installing the rear midrange speaker”,

page 76

7.1.1

Removing and installing the front bass

loudspeaker

Removing
– Switch off radio/navigation.
– Remove the front door panelings ⇒  Body Work; Rep. gr.  70 .
– Disconnect socket connector at the loudspeaker.
– Use a suitable drill to drill open the six rivets -arrows- and take

out the faulty speaker.

Note

♦

It is important to remove all the drill swarf from the door since

it can otherwise lead to corrosion.

♦

Any damage to the paintwork which is caused by drilling out

the rivets must be repaired immediately by a specialist.

Installing
– Attach the new speaker with matching blind rivets.
– Further installation occurs in reverse order.

7.1.2

Removing and installing the rear bass

loudspeaker

Removing
– Switch off radio/navigation.
– Remove the rear door panellings ⇒  Body Work; Rep. gr.  70 .
– Disconnect socket connector at the loudspeaker.

Octavia II 2004 ➤ , Octavia II 2010 ➤

Electrical system - Edition 12.2013

74

     Rep. gr.91 - Radio, telephone, navigation

Содержание Octavia II 2004












































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Octavia II 2004

Daikin CTXG09QVJUW Service Manual preview
CTXG09QVJUW
Бренд: Daikin Страницы: 254
Airwell May series Installation And Maintenance Instructions Manual preview
May series
Бренд: Airwell Страницы: 7
Technibel AO 15 GTS Installation Instructions Manual preview
AO 15 GTS
Бренд: Technibel Страницы: 16
Midea MA- 09N8D0-O Quick Manual preview
MA- 09N8D0-O
Бренд: Midea Страницы: 16
PremierOne MUV7-50DR Installation & Maintenance Instructions Manual preview
MUV7-50DR
Бренд: PremierOne Страницы: 7
Daikin MPS015 F Installation And Maintenance Manual preview
MPS015 F
Бренд: Daikin Страницы: 132
MCS BC35 User And Maintenance Book preview
BC35
Бренд: MCS Страницы: 68
EQUATION 3276007041705 Manual preview
3276007041705
Бренд: EQUATION Страницы: 45
TriStar AT-5464 Instruction Manual preview
AT-5464
Бренд: TriStar Страницы: 12
IDEAL AP0015 Operating Instructions Manual preview
AP0015
Бренд: IDEAL Страницы: 65
Argoclima AER608SCL Technical Data & Service Manual preview
AER608SCL
Бренд: Argoclima Страницы: 22
Refco Gobi II Manual preview
Gobi II
Бренд: Refco Страницы: 8
Innova IGZM218NO-1 Owner'S Manual preview
IGZM218NO-1
Бренд: Innova Страницы: 24
Winix HR950 User Manual preview
HR950
Бренд: Winix Страницы: 72
AeonAir RPAC12EF Manual preview
RPAC12EF
Бренд: AeonAir Страницы: 36
Comfee 9350436 Instruction Manual preview
9350436
Бренд: Comfee Страницы: 130
SPT SF-1515 Operating Instructions Manual preview
SF-1515
Бренд: SPT Страницы: 6
aldes NANO AIR2 CLASSIC Assembly Instructions Manual preview
NANO AIR2 CLASSIC
Бренд: aldes Страницы: 40

Бренды по названию

Популярные бренды

Загрузить еще бренды