![background image](http://html1.mh-extra.com/html/silverline/546534/546534_original-instructions-manual_1273690011.webp)
DIY 1450W Sliding Mitre Saw
546534
11
silverlinetools.com
11. Lower Blade Guard
12. Slide Rails Mechanism
13. Mitre Lock
14. Fixed Fence
15. Workpiece Supports
16. Mitre Angle Indicator
17. Mitre Angle Gauge
18. Bench Mounting Holes
19. 6mm Hex Key
20. 4mm Hex Key
21. Motor Vents
22. Bevel Angle Gauge
23. Workpiece Clamp Slot
24. ON/OFF Trigger Switch
25. Power Cord
26. Dust Collection Bag
27. Laser
28. Cutting Head Latching Pin
29. Bevel Locking Knob
30. Slide Rails Locking Knob
31. Bevel Stop/Calibration Screw
32. Workpiece Clamp Locking Knob
33. Sliding Fence Screw
34. Laser ON/OFF Switch
35. Fence Alignment Screw
36. Blade
37. Workpiece Support Screws
38. Workpiece Clamp
39. Dust Extraction Port
40. Arbor Bolt
41. Slide Rails
42. Mitre Table
43. Bevel Angle Indicator
44. Throat Plate
Intended Use
Mains powered bench-mounted or portable sliding mitre saw for cutting through wood and other
materials . Performs straight and bevel cuts . The included saw blade is suitable for natural wood and
artificial composite wood materials.
Note
: For non-commercial use only .
Unpacking Your Tool
• Carefully unpack and inspect your product . Fully familiarise yourself with all its features and
functions
• Ensure all parts of the product are present and in good condition . If any parts are missing or
damaged, have such parts replaced before attempting to use this product
Before Use
WARNING:
Important safety devices! Ensure correct function, maintain in accordance with
instructions and DO NOT disable!
WARNING:
Ensure the tool is disconnected from the power supply before attaching or
changing accessories, or making any adjustments .
Note:
Cutter/cutting head is a description of the section of the tool incorporating the motor, blade
assembly and pivoting arm . On a sliding mitre saw it is the section that traverses the pole arm or
arms .
Bench mounting
IMPORTANT:
It is recommended to mount the saw to a bench or board . Although the saw can be
used without mounting to a bench or board, there is a greater risk to safety during use .
1 . Mount the saw to a level, horizontal bench or work table using bolts, washers and locking nuts
(not supplied) through the four Bench Mounting Holes (18)
2 . DO NOT over-tighten; this may damage the base
3. Do not use bolts that are not a good fit for the Bench Mounting Holes; this may encourage
unwanted movement
4 . Alternatively, mount the saw on 13mm or thicker board, and clamp the board to a work support
(Fig . I); this makes it easy to relocate the saw, clamping it to a work support wherever needed
5 . When using a board it may be necessary to countersink the washers and nuts so the board is
level on the surface
WARNING:
Ensure the mounting surface is not warped; an uneven surface can cause binding
and inaccurate sawing .
Unlatching & raising the Cutting Head
WARNING:
ALWAYS ensure the tool is unplugged from the power socket and the blade has
come to a complete stop before latching the cutting head down, carrying the tool, and/or unlatching
the cutting head .
To unlatch & raise the Cutting Head:
1 . Press down on the Operating Handle (7) (Image A) and pull out the Cutting Head Latching Pin
(28) (Image B)
2 . Slowly raise the saw’s cutting head (Image C)
To lower & latch the Cutting Head:
1 . From the raised position, disengage the Blade Guard Safety Latch (8) (Image D)
2 . Press the Operating Handle (7) and cutting head down slowly (Image A) then press in the Cutting
Head Latching Pin (28)
Adjusting the Fence
1 . Ensure the Fence (4 & 14) is used with every cut
2 . The Sliding Fence (4) can be adjusted and extended out or removed entirely
3 . To adjust the Sliding Fence loosen the Sliding Fence Screw (33) using the 4mm Hex Key (20) and
slide the Fence to the required position (Image E)
4 . Tighten the Sliding Fence Screw using the 4mm Hex Key to secure the Sliding Fence
Note: If the Workpiece Clamp Is attached to the saw on the Sliding Fence it will require removing
before Fence adjustment can take place .
5 . If performing a bevel cut, the Sliding Fence may need to be removed so it does not obstruct the
movement of the cutting head or interfere with the Blade (36) when tilted
WARNING:
NEVER use the mitre saw without the Fixed Fence .
Adjusting the Workpiece Supports
1 . Loosen the Workpiece Support Screws (37) using the 4mm Hex Key (20)
2 . Slide the Workpiece Supports (15) into the holes on the side of the tool (Image F)
3 . Tighten the Workpiece Support Screws to secure the Workpiece Supports in position
Fitting the Workpiece Clamp
1 . Decide which side of the cutting head that the workpiece is to be clamped (normally the longer
side of the workpiece protruding from the tool)
2 . Insert the Workpiece Clamp (38) fully into the desired Workpiece Clamp Slot (23) (Image G)
3 . Tighten the Workpiece Clamp Locking Knob (32)
4 . Position the Clamp over the workpiece by swivelling the upper part of the Clamp and raise or
lower the Clamp according to the size of the workpiece (Image H)
5 . Once the clamp is in position tighten the Workpiece Clamp Adjustment Locking Knob (2)
6 . Screw the Workpiece Clamping Screw (3) clockwise to lower the Workpiece Clamping Plate (5)
onto the workpiece to clamp in position (Image I)
546534_Manual.indd 11
28/09/2018 16:16
Содержание 546534
Страница 4: ...4 A B C D E F G H I J K L 546534_Manual indd 4 28 09 2018 16 16...
Страница 5: ...silverlinetools com 5 M N O P Q R S T U V W X 546534_Manual indd 5 28 09 2018 16 16...
Страница 6: ...6 150mm 150mm 150mm FIG I FIG II FIG III FIG IV 546534_Manual indd 6 28 09 2018 16 16...
Страница 7: ...silverlinetools com 7 546534_Manual indd 7 28 09 2018 16 16...