manualshive.com logo in svg

Silicon Laboratories Si2404, Руководство пользователя


Поделиться
Скачать
background image

AN93

Rev. 1.4

23

A block diagram of the UART in the serial interface mode is shown in Figure 5.

.

Figure 5. UART Serial Interface

2.2.4. Parallel and SPI Interface Operation

Refer to "2.1. Resetting the Device" on page 11 for interface selection. The parallel interface has an 8-bit data bus
and a single address bit. The SPI likewise operates with 8-bit data transfers, using a single address bit. When the
parallel or SPI interface mode is selected, the modem must be configured for a DTE interface or 8N1 only. The host
processor must calculate parity for the MSB. The modem sends bits as received by the host and does not calculate
parity. Refer to "Appendix C—Parallel/SPI Interface Software Implementation" on page 302 for detailed parallel or
SPI interface application information.

The parallel or SPI interface uses the FIFOs to buffer data in the same way as in UART mode, with the addition of
Hardware Interface Registers 0 (HIR0) and Hardware Interface Register 1 (HIR1). The Hardware Interface
Registers were formerly called Parallel Interface Registers (PIR0 and PIR1) in older products, because those
products would support only a parallel interface. Flow control must be implemented by monitoring REM and TXE in
HIR1. There is no protection against FIFO overflow. Data transmitted when the transmit FIFO is full are lost.
Figure 6 shows the interaction of the transmit and receive FIFOs with the Hardware (Parallel) Interface Registers in
the case of a parallel interface. The arrangement is similar when the SPI interface is selected. Table 21 on page 25
shows a bit map of HIR0 and HIR1.

UART oriented control lines, such as RTS and CTS, are not used in Parallel and SPI Interface mode. They are
replaced by bits in the HIR1 register. 

SPI and parallel operation only supports 8-bit data words. The longer words that are implied by the \B5 (8P1) & \B6
8X1 commands are not allowed. These commands should not be used.

11  Bits
to Data Bus

CONTROL

RX Shift
Register

TX Shift

Register

  TX FIFO

MUX

TXD

(10)

CTS

(11)

RTS

(8)

RXD

(9)

INT

(16)

  RX FIFO

Содержание Si2404




















































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Si2404

Ultratec INTELE-MODEM How To Use Manual preview
INTELE-MODEM
Бренд: Ultratec Страницы: 32
Edimax AR-7211A V2 Specifications preview
AR-7211A V2
Бренд: Edimax Страницы: 2
Arris Touchstone CM900 User Manual preview
Touchstone CM900
Бренд: Arris Страницы: 46
LG Innotek LTD-BK1000 User Manual preview
LTD-BK1000
Бренд: LG Innotek Страницы: 27
Zte Z288L User Manual preview
Z288L
Бренд: Zte Страницы: 25
NEC Speed Wi-Fi NEXT WX01 Instruction Manual Setup Manual preview
Speed Wi-Fi NEXT WX01
Бренд: NEC Страницы: 2
NEC Speed Wi-Fi Next WX03 Setup Manual preview
Speed Wi-Fi Next WX03
Бренд: NEC Страницы: 2
upcom HPO-V35 User Manual preview
HPO-V35
Бренд: upcom Страницы: 13
THOMSON 300 Series Installation And User Manual preview
300 Series
Бренд: THOMSON Страницы: 46
Exede RM5110 Series Warranty, Safety, And Environmental Information preview
RM5110 Series
Бренд: Exede Страницы: 4
Alcatel X220 User Manual preview
X220
Бренд: Alcatel Страницы: 20
Exede WiFi Modem User Manual preview
WiFi Modem
Бренд: Exede Страницы: 12
Ebyte E90-DTU-433L33-V8 User Manual preview
E90-DTU-433L33-V8
Бренд: Ebyte Страницы: 19
3Com HomeConnect 3CR29223 Installation Manual preview
HomeConnect 3CR29223
Бренд: 3Com Страницы: 1
3Com Impact External ISDN Modem Quick Start Instructions preview
Impact External ISDN Modem
Бренд: 3Com Страницы: 6
NETGEAR DG834GV Reference Manual preview
DG834GV
Бренд: NETGEAR Страницы: 106
Fritz! Fritzbox 6660 Cable Quick Manual preview
Fritzbox 6660 Cable
Бренд: Fritz! Страницы: 12
Camatel NetVito 5300 Series Quick Start Manual preview
NetVito 5300 Series
Бренд: Camatel Страницы: 12

Бренды по названию

Популярные бренды

Загрузить еще бренды