Silicon Graphics Altix XE210 Скачать руководство пользователя страница 90

Страница: 90 / 158

SGI

Altix

XE210 User’s Guide

System Information

Use this option to view FRU data, and BMC, FRU, and HSC Revision
data.

Boot Options

Boot Timeout

Boot Option #1

Primary Master
CDROM

Boot Option #2

#300 IDM1 LUN0 ATA

Boot Option #3

IBA GE Slot 0500 v

Boot Option #4

EFI Shell

Hard Disk Order

Use this option to specify the drive order.

Network Device Order

Use this option to specify the network device order.

Boot Manager

Use this option to specify the device to boot.

Error Manager

Note: Blank.

Exit

Save Changes and Exit

Reboot=F10

Discard Changes and Exit

Goes to the Select the Boot Device option.

Save Changes

Stays in the BIOS.

Discard Changes

Stays in the BIOS.

Restore Defaults

Defaults=F9

Save as User Default Values

Saves your settings.

Restore User Default Values

Restores your settings.

Table 5. Settings on the Advanced Screen (Cont’d)

Option

Standard Settings

Differences

XE240 Active

XE210 Passive

Содержание Altix XE210































































































































































Результаты поиска

Содержание Altix XE210

Отзывы:

Бренды по названию

Популярные бренды

Silicon Graphics Altix XE210, Руководство пользователя

Результаты поиска

Содержание Altix XE210

Отзывы:

Бренды по названию

Популярные бренды