manualshive.com logo in svg

Silicon Graphics Altix XE210, Руководство пользователя

Поделиться
Скачать
Silicon Graphics Altix XE210 Скачать руководство пользователя страница 51

SGI

®

 Altix

®

 XE210 User’s Guide

35

Figure 27. Removing Hot-swap Disk Carrier from the Server System

4. Remove the four screws that attach the plastic retention device or the previously 

installed hard drive to the drive carrier. Two screws are at each side of the retention 
device or the hard drive. Store the plastic retention device for future use.

Figure 28. Removing Retention Device from Drive Carrier

5. Remove the hard drive from its wrapper and place it on an antistatic surface.

6. Set any jumpers and/or switches on the drive according to the drive manufacturer's 

instructions.

7. With the drive circuit-side down, position the connector end of the drive so that it is 

facing the rear of the drive carrier. 

8. Align the holes in the drive to the holes in the drive carrier and attach it to the 

carrier with the screws that were attached to the plastic retention device.

TP02206

A

B

TP02207

A

B

Содержание Altix XE210































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды