manualshive.com logo in svg

Silicon Graphics Altix XE210, Руководство пользователя

Поделиться
Скачать
Silicon Graphics Altix XE210 Скачать руководство пользователя страница 100

84

SGI

®

 Altix

®

 XE210 User’s Guide

Problems Following Initial System Installation

Problems that occur at initial system startup are usually caused by an incorrect installation 
or configuration. Hardware failure is a less frequent cause. If the problem you are 
experiencing is with a specific software application, see 

“Problems with Newly Installed 

Application Software”

. 

First Steps Checklist

•

Is AC power available at the wall outlet?

•

Are the power supplies plugged in? Check the AC cable(s) on the back of the chassis 
and at the AC source.

•

Are all cables correctly connected and secured?

•

Are the processors fully seated in their sockets on the server board?

•

Are all DIMMs fully seated in their sockets on the server board?

•

Are all standoffs in the proper location and not touching any components, causing a 
potential short?

•

Are all add-in PCI boards fully seated in their slots on the server board?

•

Are all jumper settings on the server board correct?

•

Are all jumper and switch settings on add-in boards and peripheral devices correct? 
To check these settings, refer to the manufacturer's documentation that comes with 
them. If applicable, ensure that there are no conflict–for example, two add-in boards 
sharing the same interrupt.

•

Are all peripheral devices installed correctly?

•

If the system has a hard disk drive, is it properly formatted or configured?

•

Are all device drivers properly installed?

•

Are the configuration settings made in Setup correct?

•

Is the operating system properly loaded? See the operating system documentation.

•

Did you press the system power on/off switch on the front panel to turn the server on 
(power on light should be lit)?

•

Is the system power cord properly connected to the system and plugged into a 
NEMA 5 15R outlet for 100-120V or a NEMA 6-15R outlet for 200-240V ?

•

Were all integrated components purchased or obtained from SGI?

Содержание Altix XE210































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды