Silicon Graphics Altix XE210 Скачать руководство пользователя страница 18

Страница: 18 / 158

SGI

Altix

XE210 User’s Guide

Table 1

summarizes the features of the server system.

Table 1. SGI Altix XE210 Feature Summary

Feature

Description

Dimensions

•

1.703 inches (43.25 mm) high

•

16.930 inches (430 mm) wide

•

27.25 inches (692 mm) deep

•

31 pounds (14.1 kg) - max chassis weight

Server Board

Altix XE210 server board

Processor

Support for up to two Dual-Core Intel

Xeon

processors 5000

sequence

Memory

•

Eight DIMM slots supporting stacked DDR2 533/667 MHz
FBDIMM memory

•

Support for up to 32 GB DDR2 533/667 MHz FBDIMM memory

Chipset

Intel

5000P chipset, consisting of:

•

Intel

5000P Memory Controller Hub (MCH)

•

Intel

6321ESB I/O Controller Hub

Peripheral Interfaces

External connections:

•

Stacked PS/2* ports for keyboard and mouse

•

DB9 Serial A port

•

RJ45 Serial B port

•

Two RJ45 NIC connectors for 10/100/1000 Mb connections

•

Three USB 2.0 ports

Internal connections:

•

One USB port header, which supports two USB 2.0 ports

•

Six Serial ATA 150 connectors with integrated RAID 0/1
support

•

One ATA-100 44-pin connector for optical drive support

•

SSI-compliant 24-pin control panel header

•

SSI-compliant 24-pin main power connector, supporting the
ATX-12V standard on the first 20 pins

I/O Control

National Semiconductor* PC87427 controller

Video

On-board ATI* ES1000 video controller with 16 MB DDR SDRAM

LAN

Dual port controller for 10/100/1000 Mbit/sec Ethernet LAN
connectivity

Expansion Capabilities

•

One low-profile riser slot supporting 1U PCI Express* riser
cards

•

One full-height riser slot supporting 1U PCI-X* riser cards

On-board Hard Drive
Controller

Six ESB2 3Gb/s SATA ports

Содержание Altix XE210































































































































































Результаты поиска

Содержание Altix XE210

Отзывы:

Бренды по названию

Популярные бренды

Silicon Graphics Altix XE210, Руководство пользователя

Результаты поиска

Содержание Altix XE210

Отзывы:

Бренды по названию

Популярные бренды