Signature Kitchen Suite UPSXB2627S Скачать руководство пользователя

Страница: 61 / 78

Shroud Housing

Shroud

HOW TO DISASSEMBLE AND ASSEMBLE

8-1. F —LAMP CASE

8-2. F —SHROUD ASSEMBLY

1) Loosen the two screws and remove

the lamp case.

2) Separate a housing and remove F-

lamp case.

1) Remove the F-lamp case.

And 2 screws marked in red.

2) To remove the Multi-Duct: 1st pull out then down then

out again.

Caution this has a tight fit, so it is necessary to pul with

some force.

3) Assembly is reverse order.

3) Separate multi duct.

NOTE

— turn the multi duct when remove it.

NOTE

— At step

③,

push the multi duct strongly.

(Because it is tight fit.)

5) Separate a housing as remarked.

6) Remove 2 screws marked in red.

And separate shroud on the way of

picture below.

7) Separate the housing as remarked.

8) When you assemble multi duct, please refer

to below instruction.

①

Insert the housing of multi duct.

②

As like above picture, please hold up back

of multi duct.

③

Then push as shown as shown below steps.

①

②

③

①

②

③

Содержание UPSXB2627S















































































Результаты поиска

Содержание UPSXB2627S

Отзывы:

Похожие инструкции для UPSXB2627S

Бренды по названию

Популярные бренды

Signature Kitchen Suite UPSXB2627S, Руководство по обслуживанию

Результаты поиска

Содержание UPSXB2627S

Отзывы:

Похожие инструкции для UPSXB2627S

Бренды по названию

Популярные бренды