Signature Kitchen Suite UPSXB2627S Скачать руководство пользователя

Страница: 65 / 78

10. Side LED Lamp cover.

1) By use a flat head screwdriver at marked in red,pull the

LED lamp cover.

2) When assembly,assemble new LED lamp cover.

Because lamp cover is easily destroyed when

disassemle step.

HOW TO DISASSEMBLE AND ASSEMBLE

9-5. R —SHROUD

6) Remove 4 screws as shown below at the grille fan.And

separate grille fan

7) Separate 2 housings connected to inner case.

8) Remove 4 screws on the shroud assembly.And remove

shroud assembly.

9) Assembly is reverse order.

1) Turn off the power of the

refrigerator (Press the POWER button

for 3 second to turn off the power).

2) Follow as shown [R-Water tank 4)]

3) Follow as shown Disassemble

compartment.

4) Remove the [R -Multi duct.]

5) turn the Water tank clockwise.

11. Guide Rail

1) Firstly pull the rail fully, and Loosen the screw shown in

the Picture. Then you can disassemble Rail guide.

Содержание UPSXB2627S















































































Результаты поиска

Содержание UPSXB2627S

Отзывы:

Похожие инструкции для UPSXB2627S

Бренды по названию

Популярные бренды

Signature Kitchen Suite UPSXB2627S, Руководство по обслуживанию

Результаты поиска

Содержание UPSXB2627S

Отзывы:

Похожие инструкции для UPSXB2627S

Бренды по названию

Популярные бренды