Signature Kitchen Suite UPSXB2627S Скачать руководство пользователя

Страница: 58 / 78

HOW TO DISASSEMBLE AND ASSEMBLE

5. HANDLE

6-1. DISPENSER DISPLAY

1) HANDLE REMOVAL

To move the refrigerator through

a house door, it may be necessary

to remove the refrigerator door handles.

Note

Handle appearance may vary from

illustrations on this page.

Loosen the set screws with a 2.5mm (3/32”)

Allen wrench and remove the handle.

Note

If the handle mounting fasteners need to

be tightened or removed, use a 1/4"

Allen wrench.

Place the handle on the door by aligning

handle footprints to fit mounting fasteners

and tighten the set screws with a

2.5mm (3/32

”

) Allen wrench.

2) HANDLE REINSTALLATION

Note

If the handle mounting fasteners need to

be tightened or removed, use a 1/4"

Allen wrench.

2) Separate housings and remember the pair to prevent

Miss assembly.

1) As below picture, separate part

①

from unit and Pull part

②

3) Loosen four screws pointed in red, separate one

housing, separate water-supply-pipe from hook.

Mounting

Fasteners

Mounting

Fasteners

Set Screw

Allen Wrench

①

②

Содержание UPSXB2627S















































































Результаты поиска

Содержание UPSXB2627S

Отзывы:

Похожие инструкции для UPSXB2627S

Бренды по названию

Популярные бренды

Signature Kitchen Suite UPSXB2627S, Руководство по обслуживанию

Результаты поиска

Содержание UPSXB2627S

Отзывы:

Похожие инструкции для UPSXB2627S

Бренды по названию

Популярные бренды