Signature Kitchen Suite UPSXB2627S Скачать руководство пользователя

Страница: 26 / 78

TROUBLE DIAGNOSIS

Items

Precautions

4. Vacuum degassing.

Pipe Connection

Connect the red hose to the high pressure side and the blue

hose to the low pressure side.

Vacuum Sequence

Open valves

①

and

②

and evacuate for 40 minutes. Close

valve

①

KEY POINT

- If power is applied

during vacuum

degassing, vacuum

degassing shall be

more effective.

- Run the compressor

while charging the

system. It is easier and

works better.

Vaccum

Pump

Yellow

Red

Blue

Low

pressure

High

pressure

5. Refrigerant charging.

Charging sequence

1) Check the amount of refrigerant supplied to each model after completing vacuum

degassing.

2) Evacuate charging canister with a vacuum pump.

3) Measure the amount of refrigerant charged.

- Measure the weight of an evacuated charging canister with an electronic scale.

- Charge refrigerant into a charging canister and measure the weight. Calculate the

weight of refrigerant charged into the charging canister by subtracting the weight of

an evacuated charging canister.

KEY POINT

- Be sure to charge the

refrigerant at around

25¡C [77¡F].

- Be sure to keep -5g in

the winter and +5g in

summer.

the amount of refrigerant charged= weight after

charging - weight before charging (weight of an

evacuated cylinder)

Indicate the weight of an

evacuated charging canister

R134a

Calculation of amount of refrigerant charged

Compressor

Low pressure side

Condenser

Drier

Hot Line

Evaporator

Drain Pipe

3 way valve

High pressure side

Содержание UPSXB2627S















































































Результаты поиска

Содержание UPSXB2627S

Отзывы:

Похожие инструкции для UPSXB2627S

Бренды по названию

Популярные бренды

Signature Kitchen Suite UPSXB2627S, Руководство по обслуживанию

Результаты поиска

Содержание UPSXB2627S

Отзывы:

Похожие инструкции для UPSXB2627S

Бренды по названию

Популярные бренды