Signature Kitchen Suite UPSXB2627S Скачать руководство пользователя

Страница: 6 / 78

Safety warnings and cautions

Caution

Do not put glass bottles or other

sealed containers in the freezer.

They may burst, leaving

glass fragments in the food

and possibly causing injury.

Be sure to use rated parts for

replacement of electric parts.

Use factory replacement parts.

Secure the cord behind the

refrigerator.

Do not allow the cord to hang

where it can be pinched,

damaged, or rolled over by

the refrigerator.

Pull the plug out by the plug body;

do not pull the wire to disconnect

the cord.

Damage to power cords

may cause fire or electric

shock.

Keep electrical parts and

connections free from dust and

contamination.

There is danger of fire

from shorting or arcing.

Be sure replacement parts are an

exact fit.

Replacement parts should look

and fit exactly like the original

parts and have the same

electric rating.

Do not let moisture drop onto

electrical parts.

If there is a problem in this area, replace the

parts or tape the wires to prevent

contamination and degradation.

If you unplug the refrigerator or

turn off the power, wait 5 minutes

before plugging it back in

or turning the power on.

Rapid cycling of the compressor

could cause failure.

Do not put your hands, fingers, tools, or other

objects into the icemaker, crusher, or discharge

outlet. Do not check the operation of the ice

dispenser or crusher in this manner.

You may damage your product, fingers, or tools.

Содержание UPSXB2627S















































































Результаты поиска

Содержание UPSXB2627S

Отзывы:

Похожие инструкции для UPSXB2627S

Бренды по названию

Популярные бренды

Signature Kitchen Suite UPSXB2627S, Руководство по обслуживанию

Результаты поиска

Содержание UPSXB2627S

Отзывы:

Похожие инструкции для UPSXB2627S

Бренды по названию

Популярные бренды