Signature Kitchen Suite UPSXB2627S Скачать руководство пользователя

Страница: 47 / 78

TROUBLESHOOTING

Result & SVC Action

Checking flow

(1)~(2)

(2)~(3)

Below 8V

0 or 5V

Change the PCB

Change the motor

SVC Action

Result

Point

Reset the unit and Input Test 1 Mode.

(push the button 1 time)

Open the refrigerator & freezer door and

Check the air flow.

Check the air temperature. Cold or not?

Check the Fan motor.

Rotate fan using your hand.

it feel sticky, change the motor.

(cause of ice or rust inside of motor)

Check the Fan motor voltage.

Pin14(2), Pin16(1), Pin18(1) of CON6.

Check the sensor resistance.

※

The sensor is determined by the

temperature.

For example, 30

㏀

indicates 0

℃

3. Troubleshooting With Error Display

17) Poor cooling in Refrigerator compartment

Motor

Sticky

Change the motor

SVC Action

Result

Point

㏀

19.5

㏀

Result

℉ /

-5

℃

℉ /

℃

℉ /

℃

℉ /

℃

℉ /

℃

(1) To (2)

Explain to customer

Check the

Compressor And

sealed system

SVC Action

Cold

Not cold

Status

Go to the 4

Check the Fan

motor(Next page)

SVC Action

Windy

No windy

Status

Содержание UPSXB2627S















































































Результаты поиска

Содержание UPSXB2627S

Отзывы:

Похожие инструкции для UPSXB2627S

Бренды по названию

Популярные бренды

Signature Kitchen Suite UPSXB2627S, Руководство по обслуживанию

Результаты поиска

Содержание UPSXB2627S

Отзывы:

Похожие инструкции для UPSXB2627S

Бренды по названию

Популярные бренды