Signature Kitchen Suite UPSXB2627S Скачать руководство пользователя

Страница: 17 / 78

Micom Function

2-11. Test Function

TEST KEY EXISTS ON PWB ASSY. MAIN BOARD.

MODE

OPERATION

CONTENTS

REMARKS

PRESS TEST BUTTON

ONCE

1. CONTINUOUS OPERATION OF COMPRESSOR

AND CONDENSER FAN MOTOR.

2. ALL DEFROST HEATERS TURNS OFF

3. 10 MINUTES IN EARLY STAGE REFRIGERATOR

FAN MOTOR ON

4. AFTER 10 MINUTES ALL FAN MOTORS ON WHEN

THE FREEZER SENSOR IS ABOVE 41¡F AND

REFRIGERATOR SENSOR IS ABOVE 59¡F

5. JUST REFRIGERATOR FAN MOTOR

ON WHEN THE FREEZER SENSOR IS

BELOW 10¡F AND REFRIGERATOR

SENSOR IS ABOVE 35¡F

6. REMAINING CONDITION FREEZER

FAN MOTOR ON

FREEZER FAN MOTOR TURNS OFF

IN FREEZER ROOM DOOR OPENING.

REFRIGERATOR FAN MOTOR TURNS

OFF IN REFRIGERATOR ROOM DOOR

OPENING.

RETURNS TO THE NORMAL MODE

WHEN THE FREEZER DEFROST

SENSOR IS ABOVE 41¡F AND

REFRIGERATOR DEFROST SENSOR IS

ABOVE 64¡F

TEST1

PRESS TEST BUTTON

ONCE AT THE TEST

MODE 1 STATUS

<Forced Defrost

mode>

PRESS TEST BUTTON

ONCE AT THE TEST

MODE 2 STATUS

1. COMPRESSOR OFF

2. ALL FAN MOTORS OFF

3. ALL DEFROST HEATERS ON

RETURNING TO INITIAL STATUS

COMPERSSOR WILL OPERATE AFTER

DELAY FOR 3 MINUTES

4. ALL DISPLAY GRAPHICS TURNS OFF

(ONLY FAILURE CODE INDICATION

PART TURNS ON “22 22” STATUS)

TEST2

NORMAL

STATUS

Содержание UPSXB2627S















































































Результаты поиска

Содержание UPSXB2627S

Отзывы:

Похожие инструкции для UPSXB2627S

Бренды по названию

Популярные бренды

Signature Kitchen Suite UPSXB2627S, Руководство по обслуживанию

Результаты поиска

Содержание UPSXB2627S

Отзывы:

Похожие инструкции для UPSXB2627S

Бренды по названию

Популярные бренды