Siemens VDO DTCO 1381 Скачать руководство пользователя страница 85

Страница: 85 / 302

Service only

Data handling

4.2 The flow of data and memory behaviour

Edition 07/2007

Technical Description DTCO 1381

4 - 11

TD00.1381.00 13

2 102

Faults (errors)

The DTCO 1381 saves faults (errors) with a resolution of one second.

The following data will be saved for every fault (error):

Calibration data

The DTCO 1381 registers and saves the following calibration data in
its data memory:

•

Programmed calibration parameters at the time point of the acti-
vation

•

The first calibration after activation

•

The first calibration in the current vehicle (depending on the
chassis number)

•

The 5 most recent calibrations

•

Date and purpose of the calibration
– Activation (1)
– Initial installation (2)
– Installation (3)
– Regularly inspection (4)

•

Name and address of the workshop

•

Number of the workshop card, issuing member state, validity

Fault

Saving regulations

Recorded data

Card faults

• The 10 most recent driver card faults

• Begin – date and time
• End – date and time
• A card’s type, number, and issuing

member state.

Recording equipment fault • The 10 most recent faults of each fault

type

• The first fault after the most recent cali-

bration

• Type of fault
• Begin – date and time
• End – date and time
• The type, number, and issuing member

state of an inserted card at the
beginning and/or end of the fault.

If several calibrations are performed on one calendar day, only the
last calibration will be saved.

Содержание VDO DTCO 1381













































































































































































































































































































Результаты поиска

Содержание VDO DTCO 1381

Отзывы:

Бренды по названию

Популярные бренды

Siemens VDO DTCO 1381, Техническое описание

Результаты поиска

Содержание VDO DTCO 1381

Отзывы:

Бренды по названию

Популярные бренды