Siemens VDO DTCO 1381 Скачать руководство пользователя страница 127

Страница: 127 / 302

Service only

Installation

5.5 Performing the installation

Edition 07/2007

Technical Description DTCO 1381

5 - 23

TD00.1381.00 13

2 102

5.5.5 Sealing the KITAS 2171 to the transmission

With sealing wire

Fig. 5 - 10: Sealing the KITAS 2171 at the transmission (with sealing wire)

If required, remove the KITAS sensor cable

(4)

from the

KITAS 2171.

Feed the sealing wire through the port of the screw

(1)

(or similar) on the transmission output.

Then lead the sealing wire through all three of the sealing eye-
bolts

(2)

on the KITAS 2171.

Lead the two-hole seal

(3)

over both ends of the wire and twist

the ends of the wire together.

Then clamp the two-hole seal with the sealing pliers, thereby
signing the seal.

Connect the KITAS sensor cable

(4)

to the KITAS 2171 via a

bayonet-type connection.

The following description describes the procedure for using the
KITAS 2171 in the integrated, screw-in version. In the case of the
other methods of installation, the procedure is identical.

Observe the instructions on sealing, see chapter 5.2.4 "Lead sealing
the DTCO 1381 components", page 5-10.

Содержание VDO DTCO 1381













































































































































































































































































































Результаты поиска

Содержание VDO DTCO 1381

Отзывы:

Бренды по названию

Популярные бренды

Siemens VDO DTCO 1381, Техническое описание

Результаты поиска

Содержание VDO DTCO 1381

Отзывы:

Бренды по названию

Популярные бренды