manualshive.com logo in svg

Siemens VDO DTCO 1381, Техническое описание

Поделиться
Скачать
Siemens VDO DTCO 1381 Скачать руководство пользователя страница 190

Service only

10.5 Performing the first calibration

First calibration

10 - 12

© Siemens VDO Automotive AG

Edition 07/2007

TD00.1381.00 13

2 102

10.5 Performing the first calibration

Definition

First calibration of the EC recording equipment.

During the first calibration the following steps must be taken at 
least:

•

Update or acknowledge all known or operationally necessary 
and legally required parameters

•

Enter vehicle registration number

•

Enter registering member state

•

Pair DTCO 1381 and KITAS 2171 "manually"

•

Check and demonstrate the proper functioning of the EC 
recording equipment

•

Measure display errors

•

Test and demonstrate that the entire system complies with the 
permissible error limits concerning distance and speed, defined 
by CR (EEC) 3821/85, annex I B

•

Check approval mark of the DTCO 1381

•

Check  sealing

•

Check tire size and effective wheel circumference

•

Check existing installation plate; create a new installation plate 
and seal it if necessary

Attention!

During the first calibration, be absolutely certain that the DTCO 
1381 is operated in the specified voltage range!

Note the legal provisions applicable in your country and check, how 
the first calibration must be performed and whether further tests of 
the EC recording equipment are prescribed within the first cali-
bration.

It is possible to access the calibration functions through the cali-
bration interface, the CAN bus diagnosis, or the K-Line diagnosis 
without a workshop card.

Содержание VDO DTCO 1381















































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды